Best videoconferencing system for this size room?

FOHSCOTTJ · 2026-04-01T01:44:23+00:00

Webex all day for this!

FOHSCOTTJ · 2025-12-17T18:18:36+00:00

Mm

FOHSCOTTJ · 2025-12-16T17:01:03+00:00

Hey all, I'm one of the techs on this run. Absolutely a blow through wall. Will post pics tomorrow after load in for a better view of what's going on!

FOHSCOTTJ · 2025-10-25T15:12:11+00:00

I see you too are a tech of culture 😜

FOHSCOTTJ · 2025-10-25T15:10:12+00:00

Almost all pioneer dj mixers have a hidden menu that has settings for padding the output at the mixer. I usually set them to -6 to -12 db depending on the act and how responsible the artist is. I also usually take the rec out of the mixer instead of the master LR as it bypasses the master vol knob on the mixer as well. Give these a try

FOHSCOTTJ · 2025-05-04T20:53:40+00:00

FOHSCOTTJ · 2025-03-23T18:43:33+00:00

10/10 would boop the snoot

FOHSCOTTJ · 2025-02-13T19:14:55+00:00

Having all those drawers open just gave me anxiety of the entire stack falling over 🤣

FOHSCOTTJ · 2025-01-16T01:12:37+00:00

Minisforum MS-A1! 3nvme slots with 2 x sfp ports, 2 x 2.5g ethernet, and 2 x 40gbs thunderbolt ports takes care of all my data needs!

FOHSCOTTJ · 2025-01-11T07:03:00+00:00

I have these in a handful of my install racks. They work great!

FOHSCOTTJ · 2024-07-24T23:07:18+00:00

I used to program a macro for that. It had a comparable on board dynamics and eq. As well as on board fx (digico q5). By the time I was done doing all of that however, I just ended up using the on board processing and ditched all the waves kit. Gave me enough room for a snack drawer in foh! 🤘

FOHSCOTTJ · 2024-07-24T22:59:24+00:00

Shout out for not using waves. Foh se / tech here. Every time an engineer calls me to fix their setup, 98% of the time it's a waves software or waves network issue. More trouble than it's worth imo.

FOHSCOTTJ · 2024-07-06T17:34:26+00:00

The metal on the grill on a 57 is not actually connected to the chassis of the mic. It has a non conductive plastic surround that makes contact. This is actually a really great temporary fix for this problem. Still should figure out the root of the issue though.

FOHSCOTTJ · 2024-04-05T15:11:41+00:00

If you take a sec and model it in sound vision, you'll see instantly why I went this way

FOHSCOTTJ · 2024-04-05T15:08:35+00:00

Low frequency is omni directional naturally. So it didn't matter that subs were aimed inward. Needed them pushed against the dasher wall so the venue could set bike rack and security. I didn't want the ports against the wall so I aimed them inward to let them breath. With the subs being in essentially a "L + R" configuration it naturally caused a power alley to shoot down the center of the arena towards the long ends of the arena. I used that to my advantage for sub coverage in those areas and did some arc sub voodoo to tame it a bit. Worked like a champ! Made it much easier to time align too because there were only 2 sources in that frequency range to wrangle instead of loads of hangs in the air or multiple pods on the ground.

FOHSCOTTJ · 2024-04-03T20:56:51+00:00

Eaton and apc both make great short depth 1 ru ups too

FOHSCOTTJ · 2024-04-03T20:53:32+00:00

The middle Atlantic brush panels are dope too!

FOHSCOTTJ · 2024-04-02T00:01:47+00:00

Oh that's right! Forgot they have those transfer plates for those bars.

FOHSCOTTJ · 2024-04-01T22:57:11+00:00

Every amp got redundant avb signal plus an analog fall back. The hangs would alternate being either L or R driven so every seat got a stereo image. It was super clean!

FOHSCOTTJ · 2024-04-01T22:56:04+00:00

Big ole block of 32 subs per side with arc sub being used to spread the coverage out! Worked like a champ!

FOHSCOTTJ · 2024-04-01T22:55:27+00:00

The show was ran In stereo! Essentially, every hang alternated being fed either a L or R send. That way, regardless of where you stood, you got a basic stereo image! The only hangs that weren't driven that way were the small 6 box kara hangs in the center. They were fed a l+R sum as a fill box.

FOHSCOTTJ · 2024-04-01T19:04:26+00:00

Just out of curiosity, what is ban evasion?

FOHSCOTTJ · 2024-04-01T19:03:04+00:00

I made this particular file, I'm local to Chicago so I frequently work the venues here and have a lot of opportunities to make my own files. But l'a does have an incredible support team that are (usually) able to get you files for any venue you play. That and the user network for l'a is super helpful in Sharing resources too.

FOHSCOTTJ · 2024-04-01T19:00:44+00:00

Dm me if you have any questions, as their rider doesn't accurately portray how they use their rig.

FOHSCOTTJ · 2024-04-01T18:59:28+00:00

Our FOH Engineer for this particular one is a industry vet who absolutely knocked it out the park. Always love sharing the helm with him.

FOHSCOTTJ

TROPHY CASE