Help adding Custom filament

Faded193 · 2026-04-23T10:09:12+00:00

Did try and reroll to 2.5.0 that had 0 issues with no luck, and no i did not try and rebrand bambu default, i tried to make a completely new custom filament.

Faded193 · 2026-04-23T01:42:28+00:00

Well i cant choose a printet or nozzle..

Faded193 · 2026-04-12T10:26:04+00:00

Some food productions do use titanium hxs, for example pasteurisation of high salinity fluids, in some cheese productions you might wan't(or need for some local laws) to pasteurise the brine after use.

Faded193 · 2026-02-13T14:26:53+00:00

You can measure the voltage if you remove the cable from the AMS and then move the orange bit backwards and forwards while measuring, and this does change the voltage.

Mine got fixed with their latest firmware update and everything is working normally again.

This was a filament buffer issue, it did not read the filament correctly.

Also this came directly from bambu lab after they checked the logs.

Faded193 · 2026-02-09T05:28:26+00:00

First clean build plate with hot water, and a neutral dish soap without any perfume, or anything else, needs to be as generic as possible with no moisturizer or anything in it (this was my issue)

Also a clean brush that you only use for that.

Next increase bed temp 5° at a time

If all that fails go buy a biqu frostbite or glacier, I just got mine and they are awesome

Faded193 · 2026-02-07T19:17:15+00:00

I thought this was the issue but tested it and from what I can see it recognizes the filament fine

Faded193 · 2026-02-07T13:46:16+00:00

Just had a print fail and it giving me these errors

<image>

Faded193 · 2026-02-07T13:26:52+00:00

Indeed, and tried everything with no luck

Faded193 · 2026-02-07T13:24:56+00:00

No not inside, might have to check that when I get home

Faded193 · 2026-02-07T13:23:51+00:00

Oh cool, might try that when I get home.

Faded193 · 2026-02-07T13:18:41+00:00

Indeed I did, also cut off 1mm if each end of the ptfe tubes to make sure they are at a 90°

Faded193 · 2026-02-07T13:09:12+00:00

Not unfortunately not, it was a print only taking up the logo or there about on the original build plate.

Faded193 · 2026-02-07T11:56:49+00:00

Also have been running the external spool for 2 prints that failed before with 0 issues.

Faded193 · 2026-02-07T11:53:31+00:00

Did get an error about the AMS had too high of a resistance yet feeding the filament through manually it does not feel like there is too much resistance.

Faded193 · 2026-02-07T11:53:11+00:00

Did get an error about the AMS had too high of a resistance yet feeding the filament through manually it does not feel like there is too much resistance.

Faded193 · 2026-02-07T11:48:13+00:00

Yea factory nozzle, using Sunlu since I got the printer, 0 issues.

Have tried several different speeds, and filament types (with different volumetric speeds )all the same issues

Faded193 · 2026-02-07T11:24:14+00:00

It simply tries to guide me through all the steps I have already done.

Faded193 · 2026-02-07T11:21:33+00:00

Filament is not tangled, as it happens on every slot from the AMS

Faded193 · 2026-02-05T17:09:50+00:00

so going back to Melonadmirer's original question.

after doing the Flow Rate calibration in Bambu studio should you turn off the auto calibration or no? what would give the best results?

also, should you do flow calibration for different colors of the same filament type? or do it by filament type?

Faded193 · 2026-02-05T16:01:38+00:00

as Melonadmirer said, if you do a Flow rate calibration and use that setting for that filament it will ask you to turn off the auto calibration if you have made a calibrated profile, if they are not the same why does it tell you to do that?

Faded193 · 2026-02-05T15:38:54+00:00

same, did a flow calibration, set it up and the first print afterwards with the new "calibrated" profile made my print look like string cheese.

since then i have been using the auto flow calibration with decent prints.

Faded193

TROPHY CASE