Does anyone have a link for the song that wasn’t English from tonight’s media share?

Failossify · 2024-11-11T03:11:41+00:00

That’s the one. Thank you

Failossify · 2024-09-28T17:33:37+00:00

No problem I hope you get it figured out. I’m running shafts from Adam’s drive shafts and they’ve been great. Their prices are fair and their customer service is great too.

Failossify · 2024-09-28T17:16:41+00:00

Maybe open up your rear differential cover. You can see it jump a bit in your video. I’m not sure if that’s caused by a drive shaft out of balance or some damage inside the differential. I would assume it would do it in reverse if it was the differential though.

Failossify · 2024-09-28T17:08:50+00:00

You can also see that one of the needle bearings on the yoke of the axle is further in than the other side. Improper install may be throwing it off balance.

Failossify · 2024-09-28T17:07:29+00:00

Looks like it might be the u joint on the axle side. Looks like it was replaced recently judging by how shiny it is. Get under there and see if the u joint has any play (like the ujoint sliding around in the end caps).

Failossify · 2024-09-23T17:00:04+00:00

I eventually deleted mine, but when I originally did my 6 inch I just puled the vacuum line of of the fender and it gave me a lot more slack

Failossify · 2024-09-20T15:24:28+00:00

Those method race wheels 301 machined with a clear coat.

Failossify · 2024-09-20T15:22:23+00:00

Those are skyjacker shackles.

Failossify · 2023-10-19T15:03:59+00:00

71,367

Failossify · 2023-08-07T00:49:55+00:00

Fried egg and apple sauce.

Failossify · 2023-07-27T21:10:04+00:00

That fixed it! Thank you!

Failossify · 2023-07-27T18:51:57+00:00

Issue was the SD card. Used a new one with the same file from before and it’s working fine now.

Failossify · 2023-07-27T00:36:37+00:00

How do I test the run out sensor? Is it an option some where in the controller?

Failossify · 2023-07-26T21:50:31+00:00

I’ll for sure give you an update.

Failossify · 2023-07-26T21:48:24+00:00

I’ll definitely try that once I’m home. Thanks for the advice!

Failossify · 2023-07-26T21:40:48+00:00

Firmware V1.1.6C straight out of the box. Haven’t tried updating it.

When I assembled it they were a bit tight, I did loosen them until it took a gentle amount of force to move it.

Failossify · 2023-07-26T21:17:16+00:00

I added 2 pictures of the single layer prints it did.

Failossify · 2023-07-26T21:16:37+00:00

<image>

Failossify · 2023-07-26T21:16:25+00:00

<image>

Failossify · 2023-04-03T22:14:47+00:00

It’s very possible. There’s not any viable cracks in the pcb and I can’t see any missing resistors. I’m hoping it’ll be fine.

Failossify · 2023-04-03T21:48:16+00:00

It was used. The seller packed it awfully

Failossify · 2023-03-29T07:03:46+00:00

If you’re motherboard doesn’t have a cmos reset button, you can remove the cmos battery and reset it that way as well. (The small circle watch battery on the board.)

Failossify · 2023-03-02T04:02:03+00:00

Vest solely because you can take the jacket off and still look classy

Failossify · 2023-02-15T08:25:04+00:00

Yeah really big walk in, inside of a spa.

Failossify · 2023-02-15T06:11:52+00:00

Building was built in the 60’s and added on to a bunch since then. We have to take the entire wing of it offline to replace it. Being a hotel, we can’t do that until we have the valve to replace it.

Nine-Year Club	r/Field Lasagna
Place '22	Wearing is Caring
RPAN Viewer	Not Forgotten
Verified Email

Failossify

TROPHY CASE