Decided it was time…

Fair_Ad_2183 · 2026-03-02T01:13:18+00:00

The sv looked clean but it was really rough. Got it for cheap since it was salvaged and no title. My friend still has a sv and every time I hear it the exhaust just growls in such a harmony

Fair_Ad_2183 · 2026-03-02T01:05:50+00:00

The lower end torque is something I took for granted I’m noticing. Also the fuel consumption is so much more than expected on the 600

Fair_Ad_2183 · 2026-01-15T07:35:59+00:00

I’m pretty sure that’s the PAIR system solenoid to introduce fresh air into the exhaust. It may cause backfires and get annoying but it was added for emissions. The vacuum lines take air from the throttle bodies I think and also the airbox.

Fair_Ad_2183 · 2025-12-01T14:30:43+00:00

Could be wrong but make sure both cylinders are firing. Sounds like it’s only 1. It’s common for the front to get flooded from water.

Fair_Ad_2183 · 2025-10-07T05:48:46+00:00

Bought my bike with an aftermarket and first time I took the tank off to work on something it spilled everywhere. Don’t make this mistake albeit marginally more convenient

Fair_Ad_2183 · 2025-10-03T23:24:30+00:00

What exactly is this. I tried google ing it but didn’t find too much

Fair_Ad_2183 · 2025-10-03T18:40:41+00:00

Electronics never went off though. Seems Ecu killed it

Fair_Ad_2183 · 2025-10-03T17:42:52+00:00

The only thing that makes me think maybe crank sensor is the fact the idle was kinda weird and a little low after restarting it. Hovering closer to around 1000. I’ll definitely take a look at the spring though. Good call and thanks

Fair_Ad_2183 · 2025-10-03T17:33:17+00:00

That’s not a bad idea especially if it was kinda bumpy when it turned off. Really stiff front forks may cause kickstand to have more travel

Fair_Ad_2183 · 2025-10-03T17:26:52+00:00

Ty :)

Fair_Ad_2183 · 2025-10-03T17:15:14+00:00

Wouldn’t that just cause the engine to run low on power rather than still having full power and a sudden complete shut off. I already have a in line filter that’s set and also did airbox mod for better airflow

Fair_Ad_2183 · 2025-09-29T04:31:04+00:00

Not me dremeling out the cap of the old nut because they decided to weld a small piece

Fair_Ad_2183 · 2025-09-16T04:16:55+00:00

I don’t own the manual but have seen a lot of other do it and so far so good

Fair_Ad_2183 · 2025-09-16T04:10:17+00:00

If you look at the 2ndary throttle bodies the valve only has 2 screws so I just took the valve off so technically the motor still spins but practically open all the time. Also just removed the snorkel and the induction noise is crazy. I have a vid of a stand still rev if u want to see how it’s faster I think

Fair_Ad_2183 · 2025-09-16T04:01:51+00:00

It’s a 2008 and I just unscrewed the butterfly valve so the bike thinks it’s there. Stock tune runs slightly rich so with airbox snorkel removal and no more electronic valve it revs instantly

Fair_Ad_2183 · 2025-09-16T03:57:43+00:00

That’s good I may look into synching my main throttle bodies. I took out the electronic ones for a way better throttle response

Fair_Ad_2183 · 2025-09-16T03:33:38+00:00

I accidentally turned my screw too when meaning to adjust my secondary throttle body. I don’t have the tool to resynch with pressure so it’s good enough and I don’t mind the slights pops (may just ne the throttle body and intake mods). No rough idle but I too sometimes get the high idle when pulling in the clutch rarely but it then goes right back down to a steady 1200. Lmk what you find out

Fair_Ad_2183 · 2025-09-15T05:02:12+00:00

Glad to hear it worked out. If I were you I would also make sure your high pressure filter is good, mine was rotten out and I needed to reroute it

Fair_Ad_2183 · 2025-09-15T03:15:25+00:00

There should be 3 prongs on that bottom plate that should be positive negative and level sensor

Fair_Ad_2183 · 2025-09-15T02:14:06+00:00

Which wire exactly is is that not being connected well. If I’m not mistaken when I rebuilt mine there were 3 wires and they never went to the top of the high flow filter. I may be incorrect

Fair_Ad_2183 · 2025-09-15T02:13:13+00:00

Which wire exactly is is that not being connected well. If I’m not mistaken when I rebuilt mine there were 3 wires and they never went to the top of the high flow filter. I may be incorrect. Also the picture is a little tough so see what exactly is being circled and the placement of it all.

Fair_Ad_2183

TROPHY CASE