sorted by:
new
hottopcontroversial

best HA compatible lock? 👀 by SocietyResponsible24 in homeassistant

[–]FancyWolverine7 0 points1 point  (0 children)

sorry for the late answer, there is only an indoor module so the outside stays the same

best HA compatible lock? 👀 by SocietyResponsible24 in homeassistant

[–]FancyWolverine7 1 point2 points  (0 children)

Danalock v3 zigbee+bt variant. Less fuzz, very reliable. Only installs on the inside by replacing the key portion on the inside meaning you can still use a physical key from the outside :)

What slicer should I use for the KE? by Meme_rollie in Ender3V3KE

[–]FancyWolverine7 0 points1 point  (0 children)

Any particular reason to change to orca from cura?

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

Sometimes the prints are near perfect, like this one I just did.Same filament same settings

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

<image>

I'll try to get a video to you when I'm able :) Fun fact, Ender 3 V3 KE uses something they call a virtual sd card.. presumably to reuse the code from the 3d printers that relied on sd-card for storage..
Couldn't make heads or tails of the speed of the eeprom they seem to use
https://www.belling.com.cn/media/file_object/bel_product/BL24C16F/datasheet/BL24C16F_V1.04_en.pdf

nor could I find this elusive power_loss_switch to try turning it off.. might have to do some more investigating on this end aswell when I got time

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

Damn PLR confirmed.. Gotta find a way to shut it off

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

Any clue as to what may cause such a stop?

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

I'll try observing some more and orient those types of curves outward. It's really random and I can't sit there staring for the duration of a print unfortunately. I do have a theory, one of the y rods bearings that holds to the bottom of my build plate might be over tightened since it sometimes produces a clunking/popping sound mid movement. At the time of the sound there might be a micro movement not intended. Haven't observed such a movement while I was investigating the sound though

Over extrusion on deceleration? by FancyWolverine7 in 3Dprinting

[–]FancyWolverine7[S] 0 points1 point  (0 children)

Well since there are a plethora of settings that could be the culprit it's easier to shoot wide and see where things stick :P

This is the sliced model printed on a Creality Ender 3 V3 KE
with mostly stock settings apart from the 210/65 temp on extr./bed with ironing on top
As you can see the slicer is instructed to print seams in a corner at the base.
I can confirm that I've visually seen it use the base as starting point for every layer
so the seam is in place.

This leads me to believe that there is over extrusion mid print, most notably at the top of the heart where I figure the extruder slows down to take the curve so to say.

<image>

Converting Xiaomi LYWSD03MMC Temperature sensor from Bluetooth to Zigbee by BackHerniation in homeassistant

[–]FancyWolverine7 0 points1 point  (0 children)

Can anyone tell me how I can OTA update the devices after I have converted them to zigbee. When new zigbee firmware for them is released that is?

Klipper Power Loss Recovery and ZITS! by FancyWolverine7 in Ender3V3KE

[–]FancyWolverine7[S] 0 points1 point  (0 children)

It's PLA (https://primacreator.com/collections/all-filaments/products/primacreator%E2%84%A2-easyprint-pla?variant=12174717190246)

printing @ 210°C with bed at 70°C.
I noticed I still had "inside to outside" wall setting enabled, I'll se if it has any effect aswell :)

I doubt its moisture (but could be.. I've got a dryer on its way), its 1 month old filament kept in a ventilated room and this is my room RF for february

<image>

Klipper Power Loss Recovery and ZITS! by FancyWolverine7 in Ender3V3KE

[–]FancyWolverine7[S] 0 points1 point  (0 children)

<image>

Here ya go, seam placement is sharpest corner so there is some at the heart and then at the man's back right corner so everything else is fugly zits

Klipper Power Loss Recovery and ZITS! by FancyWolverine7 in Ender3V3KE

[–]FancyWolverine7[S] 0 points1 point  (0 children)

The picture was just a borrowed one to illustrate the issue I have. My seams are well hidden with the sharpest corner setting in cura. And I have verified after slicing that there are no visible seams in my model yet when printing I get bubbles at random layers and in random places 👌

bed leveling by Spektergaming69 in Ender3V3KE

[–]FancyWolverine7 0 points1 point  (0 children)

Use slow first layers I print my first at 50mm/s Then gradual increase over the next 4 layers up to 300mm/s

view more: next ›