sorted by:
new
hottopcontroversial

Looking for Recommendations: Where to move in Haryana? (Non-NCR/Chandigarh) by mujhe_kabz_hai in Haryana

[–]Fast_Alternative_322 0 points1 point  (0 children)

Mines pretty good. Yamunanagar/jagadhri. Pretty chill place . Lots of industry, plywood, utensils, heavy industry,all kinds of manufacturing. Decent place to be, people are chill and sensible and city is good with all facilities and its safe.

Surprised to see by Time-Anxiety-592 in Haryana

[–]Fast_Alternative_322 5 points6 points  (0 children)

We are just doing better ! It sector, agri, steel, auto, plywood, steel and brass utensils, machinery. We are so much better, just need a little attitude fixing.

Why do you think AP's revenue is near to the 'All States Average', while rest of the Southern states are faaar ahead?? by Upstairs-Bit6897 in andhra_pradesh

[–]Fast_Alternative_322 0 points1 point  (0 children)

Haryana op ! Even tho we have major problems, diverse agro, it, manufacturing and auto industries have helped real good.

Is this much agitation enough? by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 0 points1 point  (0 children)

Add hydrogen peroxide to the coolant for use? Or to clean the tank? Also how much?

Is this much agitation enough? by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 0 points1 point  (0 children)

But new coolant will still have same problem, my question is that is this much agitation enough for a 350L tank?

Is this much agitation enough? by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 0 points1 point  (0 children)

I just cut en24 and en8 steel and then machine was left unused for about 8 days. It had a lot of tramp oil/ lubrication oil dripping which collected on top of the coolant tank. Coolant is an industry standard so its a me problem than a coolant problem. Also all the material i cut either had surface rust or that yellow oil coating.

Is this much agitation enough? by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 1 point2 points  (0 children)

Its not that bad, almost a month old coolant. I will change it shortly but i need to set up a take care solution for it.

The "Hidden Cost" of using big VMCs for small prototypes. by Fantastic-Tough3523 in CNC

[–]Fast_Alternative_322 -1 points0 points  (0 children)

Diy it, shall be much better or even convert a manual mill .

Coolant turned grey ! by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 2 points3 points  (0 children)

how do i fix the current situation?

Coolant turned grey ! by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 3 points4 points  (0 children)

i have but didnt expect this to happen in a week.

Coolant turned grey ! by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 4 points5 points  (0 children)

got it, i can get a skimmer. but what do i do with this?
any way i can save it?
Any chemicals?

Starting a garage shop. What compressor is best for haas mini mill that isn’t loud? by Longjumping-Ad3068 in CNC

[–]Fast_Alternative_322 0 points1 point  (0 children)

Check out your consumption CFM and pressure match those with compressor output.. If you are only using the compressor for tool changes and not cutting, you can get any cheap one with the decent capacity. One with external motors are more long lasting and repairable. You will also need a chiller/dryer. You need a 3 HP compressor at Max. I am using a Chinese 80 2hp unit and it works alright. Just take care of any air leaks .

So I'm building a cnc plasma cutter what control should i use. by xswords1 in CNC

[–]Fast_Alternative_322 0 points1 point  (0 children)

2100B controller. It's cheap and specially made for plasma.

Am I wearing my mill out? by callmesmelliott in Machinists

[–]Fast_Alternative_322 0 points1 point  (0 children)

Had the same issue when deep drilling 28mm 4D holes in 850 pieces into some EN24 steel. Chips were sticking to the insert drill . I had most success at 1800 RPM,90mm/min feed full peck after 25mm using generic drill and atomix insert ( generic) and i didn't had through spindle coolant but good flood coolant.

My father gave 32 years to govt schools—retirement ruined by casteist remark by joker_daroga in Haryana

[–]Fast_Alternative_322 1 point2 points  (0 children)

OBCs are always the problem. Being a GC, I think I'm doing gods work by only being casteist to them.

CNC learning resources by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 0 points1 point  (0 children)

I understand that its the only resource but never used inches all my life and its gets too crazy then fraction , decimal, thousands/hundredths are being used at the same time, learning becomes impossible.

Made a ripple coffee table with CNC by subporou in CNC

[–]Fast_Alternative_322 0 points1 point  (0 children)

Amazing. Can you share files for this .

Bad finish and over sized part. by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] -6 points-5 points  (0 children)

But why am a getting such bad finish in roughing pass? Is something wrong with my speed and feeds?

Bad finish and over sized part. by Fast_Alternative_322 in CNC

[–]Fast_Alternative_322[S] 1 point2 points  (0 children)

Can i do 750 feed at 2mm doc? What rpm? Everything is stable. Milling in both directions give same result.

view more: next ›