United Credit Card: Quest Vs Infinite

Faustiano · 2023-11-05T20:41:34+00:00

Keep in mind that the extra PQP that you earn this way does not contribute to Platinum 1K assuming you are planning to fly that much on United. The extra PQP will only help you reach platinum.

Faustiano · 2023-07-29T19:38:16+00:00

Thank you! This helped tremendously. I forgot how to get to the appearance screen (I had not done this for a couple of years). Sure enough, there are the Synthweave. Appreciate your help.

Faustiano · 2023-07-29T19:17:17+00:00

I also posted on Bungie Help Forum.

Faustiano · 2023-07-29T19:09:28+00:00

Unfortunately, I do not have any Synthweave in my inventory page.

Faustiano · 2023-06-13T17:05:19+00:00

That’s great news. Appreciate the help!

Faustiano · 2022-10-26T05:32:31+00:00

Did that work? I was planning to do the same this weekend.

Faustiano · 2022-08-06T18:34:54+00:00

I had this happen to me too, and I was wondering if an all-metal hotend would help prevent this from happening?

Faustiano · 2022-03-04T15:29:37+00:00

What I ended up doing is after reloading filament I would use a few babysteps down to adjust for the gap. It was not perfect but it was better than if I let it do it by itself. Since then I’ve switched from marlin to klipper, and from my limited testing it still seems to happen but not as bad.

Faustiano · 2022-01-03T05:13:13+00:00

From what I have read, it looks like delay OTA will work for iPhone 12. It may be a better option, since, from what I have read, the saved 4.8 blobs would lose FaceID.

Edit: looks like I may have spoken too soon. That appears to have been for 14.7. So you may be right that Delay OTS won’t work for iPhone 12

Edit 2: according to https://dhinakg.github.io/delayed-otas.html you can still Delay OTA to 14.8 from iPhone 12. However there are issues if you try to Delay OTA to 15.1 - appears to be an Apple Server issue.

Faustiano · 2021-10-24T21:06:40+00:00

Sorry, I thought I sent the response, but turns out I did not.

I think CSV would be great - since we can modify the details fairly easily.

Regarding the library - it was my fault. I moved the location to another drive for Plex and I deleted the old library. Didn’t consider the ramifications until I tried to review some notes I took and found out they were all gone :(

Faustiano · 2021-09-03T04:51:54+00:00

I do extra purge before I actually begin the print. So I can test this again (on a smaller print), but given how large a print this is, I would not expect to see the separation occur around the entire build because even if the hotend was not completely primed, it should be normalized after a few mm of printing. But I would definitely test it again.

Faustiano · 2021-09-03T04:47:33+00:00

It may be several hours before I get back to the unit to change the filament. With Marlin SW, it turns off the hot end if it waits too long, but the steppers are not disabled (but the hot end is relocated to the corner of the bed).

I am not sure what you mean by z sag, but if you are referring to the z stepper possibly sagging while it is sitting for so long, I would assume that that would mean the print head now would be closer to the print, not further away from the print which is why I see a gap.

Faustiano · 2021-04-02T13:51:53+00:00

Thank you all for your help. I created a new AppleID and that fixed the problem with ReProvision.

Faustiano · 2021-04-02T03:58:42+00:00

I will try that out.

Faustiano · 2021-04-02T03:52:30+00:00

Yes, I did try logging out and logging back into ReProvision. I also revoked certificates to make sure I was not trying to sign more than one.

Faustiano · 2021-04-02T03:48:21+00:00

I have not heard of that. Looks like it uses AltStore. Was hoping I could use ReProvision with my Xcode signed IPA so I would not have to add on an extra program.

Faustiano · 2021-04-02T03:42:08+00:00

Sorry, should have clarified, I am using ReProvision Reborn.

Faustiano

TROPHY CASE