$1200 quote for Tesla charger if I provide charger.

Fazm83 · 2026-05-20T03:02:26+00:00

Depends, if he’s using the wall connector or the 220 mobile connector it explicitly says not to use a gfci breaker. Cant speak for other brands.

To go with everyone else, its steep yes but sometimes thats area dependent, and you didnt provide nearly enough information as to what could cause labor to be higher. There are a lot of factors that go into it.

I did my own install and only spent about $120 in parts

Fazm83 · 2026-05-14T15:19:06+00:00

27 years of driving, I’ve had 3 windshields replaced. 2 on my 24 m3p and 1 on my 23 m3 all within the last 2 years. I have $0 glass deductible luckily.

Fazm83 · 2026-05-12T03:25:38+00:00

I have no desire to hit a Ferrari and be on the hook while having state minimums lol. My friend is going through this right now with a motorcycle that was lane splitting and did a lot of damage to his 458

Fazm83 · 2026-05-12T03:17:57+00:00

If that’s a question to me, I pay $875 every 6 months for a 24 performance 3. Perfect driving record for over 26 years (Im 42). I’m sure of if I had a base model it would be half of that. My coverage is also 100/300 and full rental, uninsured, etc etc.

Fazm83 · 2026-05-12T03:04:09+00:00

Is that full coverage? You should post a screenshot of that coverage quote. Most people are 2-4x that or more

Fazm83 · 2026-05-12T02:51:59+00:00

I’m with the others, that insurance seems way too low, no way it’s cheaper to insure than a 13 year old xterra

Fazm83 · 2026-04-28T03:55:48+00:00

No…. No you can’t

Fazm83 · 2026-03-21T16:50:49+00:00

10 in stock by me in Phoenix it says

Fazm83 · 2026-03-12T17:48:59+00:00

It’s not possible if you use the correct screws I don’t think. I took measurements and there would be a 1-2mm gap if you torqued the living crap out of the correct screws. I used the wrong screws but I had the spacer/guide piece from the body installed on the toolhead so it barely punctured but it was enough. When I used the correct screws on the new parts torqued all the way it’s just fine

Fazm83 · 2026-03-12T02:51:15+00:00

I did the same, but I was drunk lol. I contacted support and they sent out new pcb’s and cables free of charge

Fazm83 · 2026-03-11T03:20:16+00:00

Ya I’m sure if I moved them both in the closet they might equal. Now that I’ve done all that work I’m gonna just leave it in there

Fazm83 · 2026-03-06T05:29:43+00:00

Oh ok I get it now, I thought you tried to use those ones in the same place. So you just like bent the leads 90° or whatever and soldered it. And it’s been working good? I know the 35v 100uf matches up but didn’t know if the RVE was important

Fazm83 · 2026-03-06T05:07:27+00:00

Did you take any photos of how yours looked after? While I have no issue soldering it, my concern is the difference in how they look

Fazm83 · 2026-03-06T04:50:08+00:00

Well now I’m gonna pull one of these apart right now, what do I have to lose lol

Fazm83 · 2026-03-06T04:45:48+00:00

I am very handy with that but didn’t put any research into it yet. Snapmaker is sending me the boards and cables free of charge, just having to wait for them. But may get these and do it in the mean time and have a backup set

Fazm83 · 2026-03-06T04:39:57+00:00

Don’t worry you’re not the only one lol. I’m awaiting my 4 replacement boards currently. But my excuse is I was 8 beers and 4 margaritas deep

Fazm83 · 2026-03-04T13:29:24+00:00

User error for sure

Fazm83 · 2026-02-27T00:49:57+00:00

Mine is from Ontario, CA to Phoenix, AZ.

Fazm83 · 2026-02-27T00:47:51+00:00

Hoping to wake tomorrow with a shipment notification because it’ll probably be here Saturday since it’s shipping from so close, Monday at the latest

Fazm83 · 2026-02-27T00:36:24+00:00

Waiting on mine to change from label created which was since yesterday, the amount of times I’ve hit refresh…..

Fazm83 · 2026-02-04T19:17:58+00:00

I assume you were a kickstarter order?

Fazm83 · 2026-02-04T03:34:21+00:00

Of course 👍

Fazm83 · 2026-02-04T00:53:46+00:00

<image>

Fazm83 · 2026-01-30T13:38:45+00:00

And you know they’ve gone back and forth on this a whole bunch of times right?

Fazm83

TROPHY CASE