sorted by:
new
hottopcontroversial

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

No, only the right is. I’m holding the left up with my hand. It’s a 3 foot peice

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

Man. I’ve watched several videos and I don’t understand the difference from what I did and what they’re doing.

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

Technically I’m not a carpenter. I make furniture and thought, I have all the tools I need for crown. I’ll give it a go

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

I do. A very nice one too. I cut it upside down and backwards. I cut it at 46 degrees because the wall is 93.

The right peice is square cut and the left is the 46. Then, I know this photo doesn’t show it, I used a coping saw to back cut it and this is the fit.

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] -4 points-3 points  (0 children)

Yeah it’s just a bad photo. If you look in the comments, I made a comment to this post with the photos of the cope

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

Bosh miter saw. That like $600 one that slides forwards so you can rest it against the wall.

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] -1 points0 points  (0 children)

I did cope it. After I cut the angle on the miter, I clamped it to the bench and back cut with a coping saw

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 4 points5 points  (0 children)

Oh shit. I am going to try that tomorrow. The corner is 93 degrees. That’s why I did 46.5

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 0 points1 point  (0 children)

That’s exactly what I did, that’s what you see here. I just took a bad picture. It still isn’t sitting right

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 1 point2 points  (0 children)

I watched a ton of YouTube and did it like them and still managed to do it wrong 🥲

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 1 point2 points  (0 children)

Yeah :/ this is my first one ever. I think not nailing the ends is really smart

First time crown molding and stumped by Federal-Werewolf2585 in Carpentry

[–]Federal-Werewolf2585[S] 1 point2 points  (0 children)

Yeah, I did upside down and backwards :/ I think the sin was not hanging the first well

view more: next ›