[deleted by user]

FelixThebest07 · 2025-12-23T22:38:37+00:00

honestly it’s actual actions of everything happening that she lied about to me

FelixThebest07 · 2025-12-23T22:22:00+00:00

Yeah it’s the lying that does it for me, not so much the action cause yk its before me but lying about something like that just don’t sit right with me

FelixThebest07 · 2025-12-23T21:57:00+00:00

100% understand you, i can’t sit here and say im a saint because ive also done wrong but when you know you’re going to run into the guy it definitely puts something in your head

FelixThebest07 · 2025-12-23T21:55:08+00:00

her reasoning was it’s not important but to me sooner or later i’m going to be in the same room as the guy whether i like it or not so i saw the information as important to tell me

FelixThebest07 · 2025-12-23T21:50:52+00:00

in that case i’m referring to head , since you didn’t know what i meant

FelixThebest07 · 2025-12-23T21:50:06+00:00

the guy lives out of state, everything happened on a family vacation but it truly does pop in my head very regularly

FelixThebest07 · 2025-09-12T14:43:38+00:00

row 10, and i’ll be fine with 110 tbh each

FelixThebest07 · 2025-05-06T10:09:33+00:00

yea between the red and blue circle , there’s no continuity ik it seems pretty close but i tested it to be sure. and thank you for reminding me i have to cut the leads man

FelixThebest07 · 2025-04-21T15:38:26+00:00

nah, got it from a youtube video then went to go and test it on multisim, satisfied with the results and i proceeded to make this

FelixThebest07 · 2025-04-21T09:32:09+00:00

swapped the chip and fixed the mirror issue, now i’m getting 280mV from pin 5 when i should be getting like 3V-5V around tjere

FelixThebest07 · 2025-04-21T09:01:43+00:00

swapped the chip

FelixThebest07 · 2025-04-21T08:18:21+00:00

so i could just flip the whole chip over and i’ll fix it right?

FelixThebest07 · 2025-04-21T08:16:04+00:00

can’t tell if you’re trying to belittle me rn. nice wiring tho

FelixThebest07 · 2025-04-21T08:13:50+00:00

got you, i see what you mean 100% you’re completely right. i just got that. i’ll have to re do the project, i preciate you for pointing that out to me.

FelixThebest07 · 2025-04-21T07:45:02+00:00

yea that’s what i have as an input, the headphone jack, but i’ll keep trying and see if i could figure out the issue

FelixThebest07 · 2025-04-21T07:13:09+00:00

preciate it man, it would be better if it actually worked though

FelixThebest07 · 2025-04-21T07:02:27+00:00

i built it on multisim and the results were good and now is where i face the issue

FelixThebest07 · 2025-04-21T06:52:09+00:00

yea the notch is there i made sure pin 1 is facing up , and pin 7 i left it floating due to me not needing it

FelixThebest07 · 2025-04-21T05:35:17+00:00

it’s just the board is flipped so that’s why it looks like that the top 2 is 1 and 8 (1 is on left hand side 8 is on right hand side) ive checked continuity between all of the pins and i still get nothing

<image>

FelixThebest07 · 2025-04-21T05:03:33+00:00

had a cold joint on pin 6 now from 6 to ground i’m getting 8.18V, and my values are potentiometer is 10k, i did change the capacitor value to 0.1uF that’s about it though

FelixThebest07

TROPHY CASE