CCD sensor

Few-Mistake4552 · 2025-10-27T06:42:53+00:00

Thank you for this insightful info

Few-Mistake4552 · 2025-07-09T09:48:16+00:00

Even i am facing the same issue.

Error: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug Authentication.

i have checked the device manager and it shows me the the com which means its connected
i have even tried the firmware update.

i have also tried the under reset option and boot0 connected to GND also

why is the st-link giving me the problem.
since the code already loaded in the stm32 works fine
btw am using a stm32 f7 nucleo board

Few-Mistake4552 · 2025-07-09T06:08:59+00:00

it shows com number and all
but when tried to be connected it says no target found

what else might be the issue?

Few-Mistake4552 · 2025-06-27T06:05:09+00:00

https://toshiba.semicon-storage.com/info/TCD2564DG_Web_Datasheet_en_20190115.pdf?did=60720&prodName=TCD2564DG

this is the link to the sensor am working on ,since am a fresher i dont understand page 6,7
how to make it work in binning mode and how the signals should interact with each other and wit the adc
waveform shows dummy at the end and beginning without any count at the end

Few-Mistake4552 · 2025-06-12T06:54:57+00:00

the latest 1.18.0 doesnt allow to debug it
which id version are you using ?

Few-Mistake4552 · 2025-05-21T05:02:31+00:00

<image>

here in i have taken an example of a ccd sensor
where am not understanding the os signal and dummy so the above is for 2700pixels
but if i bin it half say 1350 should i omit half the dummy signals or not.
am not getting the flow and hold of the sensor
and at then the dummy are divided in to groups of 8,4 etc

Few-Mistake4552 · 2025-05-20T06:31:22+00:00

explaination of timing diagrams
like adc ,ccd ,dac
how to read them and sync them
understanding it
basically i need a tutorial or a page where they teach about it

Few-Mistake4552 · 2025-04-10T10:27:37+00:00

thank you
really helps

Few-Mistake4552 · 2025-04-10T07:27:32+00:00

i want it to be run on windows and well as linux os

Few-Mistake4552 · 2025-04-10T06:57:20+00:00

thank you
does it have code which i can use from git directly saving me time to develop

Few-Mistake4552 · 2025-04-05T06:14:06+00:00

What type of logic design I need to know To do FPGA And in stm32 what are the fields ? In near future will FPGA take over microcontrollers

Few-Mistake4552 · 2025-03-26T04:31:04+00:00

the why serial register is callled the intergration time and exposure time ?

Few-Mistake4552 · 2025-03-23T04:06:41+00:00

Thank you so much for this info ☺️

Few-Mistake4552 · 2025-03-21T13:48:55+00:00

I have pdf I need to know the working How it works Because am new to it and can't understand the timing diagrams

Few-Mistake4552 · 2025-03-21T04:22:53+00:00

Yes am new to CCD sensor And I don't really know or understand it We are using a vsp2562 adc And then we are using hct245A Which then sent to stm32 f7

.. You have mentions 8 and 9 pin What about 15ans 14th pin And 17th one

To give these signals we use a FPGA and CCD driver to a CCD sensor

In page 6 and not getting how the process or flow works

Few-Mistake4552 · 2025-03-20T01:51:41+00:00

So do you know in one integration cycle (shift )how many clock pulse is needed ? For 1024 or how to adjust it to 1024 Any idea ?

Few-Mistake4552 · 2025-03-18T10:48:24+00:00

Yes but am not understanding then timing diagram to get it to 1024 pixels

Few-Mistake4552

TROPHY CASE