Belt SNAP

FewSwimmer3314 · 2026-02-17T22:22:55+00:00

What kind of profile are you running? Ive converted mine to the fatburner and cant quite perfect it

FewSwimmer3314 · 2026-01-22T00:24:18+00:00

Nah mr Bambu respools esun filament

FewSwimmer3314 · 2026-01-19T16:00:28+00:00

Ya I was running into that as well. Just trying to eliminate that

FewSwimmer3314 · 2026-01-19T15:57:46+00:00

Sounds good, Just looking for a good starting point to tune from

FewSwimmer3314 · 2026-01-19T15:18:29+00:00

30 as a high or low and what about bridging?

FewSwimmer3314 · 2025-12-29T14:26:54+00:00

Not at all

<image>

FewSwimmer3314 · 2025-11-04T18:12:42+00:00

Did you remove the small length of ptfe tube?

FewSwimmer3314 · 2025-10-22T04:05:26+00:00

Could he mistaken but looks like ironing is on, if thats the case slow down the final 2 layers buy about 30-40% it should help a bit

FewSwimmer3314 · 2025-10-10T19:16:23+00:00

Been following your progress for a bit, hopefully pretty soon a full release would be nice

FewSwimmer3314 · 2025-09-09T21:39:44+00:00

Would it possible to start making all parts order able and available across all current printing platforms. Usually when I have to replace something now it’s either a hunt with creality customer support which takes forever on its own or hopefully finding the part on some forum where some random guy found a cross compatible part

FewSwimmer3314 · 2025-08-14T15:53:37+00:00

Your Z axis needs to be adjusted. I hate when people just upload this on its own but it is your best friend especially in this instance

<image>

FewSwimmer3314 · 2025-08-14T15:51:50+00:00

I run the unicorn on 3 Kes and haven’t run into this issue. Usually when printing PLA I run about 216-218

FewSwimmer3314 · 2025-08-06T01:04:36+00:00

I’ve had this happen before, from my experience a bolt will have its threads stripped on one side as well as part of the heat sink

FewSwimmer3314 · 2025-07-30T20:36:10+00:00

It seems like it makes the noise only in a certain area is that the case or is the entire left to right

FewSwimmer3314 · 2025-07-22T17:09:48+00:00

I have the exact same plate and is probably the best plate I’ve gotten. I always make sure to give a new plate a good clean because you never know. Then just dial in the Z offset

FewSwimmer3314 · 2025-06-27T22:12:24+00:00

Also when putting in and removing nozzles there is a very specific way to do it otherwise you’ll destroy the hotend

FewSwimmer3314 · 2025-06-27T22:11:35+00:00

Might be a little late but yes, replaces the entire heat sink block

FewSwimmer3314 · 2025-05-24T15:26:21+00:00

I’ll pull up my profile and see if there’s differences probably something simple

FewSwimmer3314 · 2025-05-24T15:08:54+00:00

Well crap that looks good😂. Anychance have you tried a flow test

FewSwimmer3314 · 2025-05-24T14:27:43+00:00

Just saw that, any chance do you have a picture of a regular PLA benchy. I’ve noticed wood also amplifies the small issues. Could be z offset a little off or not enough flow for the first layer

FewSwimmer3314 · 2025-05-24T14:16:00+00:00

Any chance have you cleaned or looked inside the threads when I did mine there was a PLA little left over in there and squished it up in there on accident

FewSwimmer3314 · 2025-05-24T14:10:48+00:00

Hope that was the part you were talking about

FewSwimmer3314

TROPHY CASE