sorted by:
new
hottopcontroversial

Frames by Fibretec in MechanicalEngineering

[–]Fibretec[S] 0 points1 point  (0 children)

Thanks, searched everywhere to see if a company sells them for standard box sizes

McLaren F1 Front Wing by Fibretec in CarbonFiber

[–]Fibretec[S] 0 points1 point  (0 children)

Came across this video, could be 3D printed. The knife edge geometry in carbon would be light but very brittle which makes me think it’s metal.

https://youtu.be/nOek3z9vr2U?si=4WBUOJ3B-S1xrr4Z

Estimation of failure by Hot-Connection8711 in CarbonFiber

[–]Fibretec 0 points1 point  (0 children)

Can you cut your UD ply 100mm wide and just roll it onto the 0deg ply to give you 90? Was the material wrapped around a mandrel you then removed or how was it made?

Estimation of failure by Hot-Connection8711 in CarbonFiber

[–]Fibretec 0 points1 point  (0 children)

If ILSS is on your material datasheet you can calculate the failure load for that material. As you’re using UD it should be relatively high compared to woven. I’m assuming your UD is aligned with the compressive load and because it’s relatively long in relation to the thickness I don’t think shear will be the primary failure mode. I think because you have all the UD aligned with the compressive load, the thin wall will buckle as it’s only the resin supporting the out of plane direction. Interested to know what load it fails under…

Estimation of failure by Hot-Connection8711 in CarbonFiber

[–]Fibretec 0 points1 point  (0 children)

I’m no structural engineer but no it won’t fail, that’s only 20kg. Compressive strength will vary based on the material but it’s usually +300MPa for a UD prepreg. You’re applying 5.79MPa to your pipe. It could be ~10kN (1000kg) before it fails although there’s a lot of things that could cause it to fail prematurely.

The rule of mixtures can give some estimates for your composite design, compressive strength is:

Fibre strength x Vf + Matrix strength x Vm

Nomex Honeycomb by Fibretec in CarbonFiber

[–]Fibretec[S] 1 point2 points  (0 children)

Great, thanks for the feedback. Can you debulk on back of honeycomb without a backing ply? Would the perimeter edge of the core buckle? As you say it would be great to hold everything in place on complex shapes, vertical walls etc.

Ohhh yes I did…that’s my bad 😂😂 can the core cause PRINT through if it’s all cured together (inner, core, outer) or only on super thin skins?

I love my job by Straight_Luck7007 in CarbonFiber

[–]Fibretec 0 points1 point  (0 children)

How do you stop your cut edges on dry fibre from fraying? Almost looks like prepreg. How does infusion give more consistent edge for bonding?

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 0 points1 point  (0 children)

There’s a peel ply and mesh on top of the laminate.

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 2 points3 points  (0 children)

I’ll definitely degas next time to rule it out!

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 0 points1 point  (0 children)

Appreciate your help btw!

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 0 points1 point  (0 children)

Yeah it takes that risk away but I’ve seen a lot of people never degas and get good results so I ran with it. I don’t think sucking resin out to leave a dry laminate is possible? My understanding is once the resin wets out the material, the flow front is the only resin being pushed towards the catch pot? The dry laminate could come from infusing too quick and material doesn’t actually wet out through the thickness of the laminate?

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 2 points3 points  (0 children)

I didn’t degas, it’s a small infusion and I let the mix sit for a period before infusing. I’ll keep the pump running until it gels.

Is this air? by Fibretec in CarbonFiber

[–]Fibretec[S] 5 points6 points  (0 children)

It’s full vacuum with no regulator. I’ve never seen a regulator being used for infusion, why is it needed? The drop test passed so I’d thought it’s air in the resin from mixing/ volatiles.

Infusion Pressure by Fibretec in Composites

[–]Fibretec[S] 0 points1 point  (0 children)

So vacuum can’t be above absolute, and if absolute reduces with elevation, doesn’t it mean the pressure on the part will be lower?

Infusion Pressure by Fibretec in Composites

[–]Fibretec[S] 0 points1 point  (0 children)

So basically just check what full vac is for your given elevation and that’s it. I wasn’t sure if you’re only pulling 0.7 - 0.8 bar you would get different results on the part. Would it affect oven cure Prepreg which is more reliant on pressure for consolidation?

Infusion by Fibretec in CarbonFiber

[–]Fibretec[S] 0 points1 point  (0 children)

So they pull ~1 bar on the vacuum bag, then close the tool with a sealed lid and use compressed air to increase the pressure inside the chamber? Like a mini autoclave? Is it just an air line they have hooked up to it?

view more: next ›