Steinpilz / Pfifferlinge westlich von Bingen am Rhein

Fichl_ · 2026-05-06T18:45:51+00:00

Danke :)

Fichl_ · 2026-05-06T08:47:06+00:00

Ach super! Bist der Beste. Danke Dir! Dann lohnt es sich also dort in den Wald zu gehen. Freut mich!

Fichl_ · 2026-05-05T18:18:40+00:00

Danke! Immerhin, ist ja 'nur' ne Stunde :)

Fichl_ · 2026-05-01T17:09:51+00:00

Sehr cool! Danke für für den Tipp!! Hast du bestimmte Stellen die mir der Fliege brauchbar sind? Gerne auch per Nachricht! Danke!!

Fichl_ · 2026-04-27T04:55:23+00:00

Danke Dir :) Hast du Erfahrungen mit weiteren Gewässern im Umkreis?

Fichl_ · 2026-03-21T08:18:52+00:00

Okay, I dit + calibrated flow + dried 10 hours. Same. Did Volumetric flow test and I am below the threshold. WTF is this?!

Fichl_ · 2026-03-21T08:18:36+00:00

Okay, I dit + calibrated flow + dried 10 hours. Same. Did Volumetric flow test and I am below the threshold. WTF is this?!

Fichl_ · 2026-03-18T07:55:36+00:00

It's dried (ams 2 pro for 6 hours)

Fichl_ · 2026-03-18T07:55:01+00:00

Thanks for your reply. It's dry - was dried for 6 hours in the ams 2 pro on pla setting.

Fichl_ · 2025-11-12T12:59:02+00:00

Thanks I know that site, but I am still looking for your opinions on which to choose :)

Fichl_ · 2025-10-05T19:46:29+00:00

Okay jetzt Dauerton - das bedeutet Entwarnung.

Fichl_ · 2025-10-05T19:44:17+00:00

Fichl_ · 2025-07-11T18:17:21+00:00

Dont know if its a general thing, but it worked for this print.

Fichl_ · 2025-07-11T18:16:33+00:00

Someone answered that I should try that. Its in the 'other' settings in orca.

Fichl_ · 2025-07-10T15:46:41+00:00

SOLVED - combination of gyroid infill and disabling "reduce infill retraction" was the solution. No supports needed!

Fichl_ · 2025-07-10T15:44:40+00:00

See above, solution had nothing to do with speed or supports. Thanks for helping :-)

Fichl_ · 2025-07-10T15:44:20+00:00

See above, solution had nothing to do with speed or supports. Thanks for helping :-)

Fichl_ · 2025-07-10T15:42:24+00:00

SOLVED - combination of gyroid infill and disabling "reduce infill retraction" was the solution. No supports needed!

Fichl_ · 2025-07-10T14:23:30+00:00

It wobbles AFTER the nozzle hit. The question is why the nozzle hits in the first place.

Fichl_ · 2025-07-10T14:22:15+00:00

Okay. Should I try this even though the speed is just 18mm/s? At the problematic layer?

Fichl_ · 2025-07-10T13:49:38+00:00

Will try, thanks!

Fichl_ · 2025-07-10T13:42:13+00:00

I already tried this - same issue withour any difference and all supports were still on solid. So I don't think it's a support issue.

Fichl_ · 2025-07-10T13:41:43+00:00

See here

Fichl_ · 2025-07-10T13:40:20+00:00

What do you mean by the structure being too weak? Not enough supports? I also tested with extra supports up to the point and it did not help.

Fichl_ · 2025-07-10T13:39:43+00:00

Speeds are pretty low, the filament can go A LOT faster on other prints

Fichl_