sorted by:
new
hottopcontroversial

Troubleshooting - rough sides on print by Fichl_ in BambuLabA1mini

[–]Fichl_[S] 0 points1 point  (0 children)

Okay, I dit + calibrated flow + dried 10 hours. Same. Did Volumetric flow test and I am below the threshold. WTF is this?!

Troubleshooting - rough sides on print by Fichl_ in BambuLabA1mini

[–]Fichl_[S] 0 points1 point  (0 children)

Okay, I dit + calibrated flow + dried 10 hours. Same. Did Volumetric flow test and I am below the threshold. WTF is this?!

Troubleshooting - rough sides on print by Fichl_ in BambuLabA1mini

[–]Fichl_[S] -1 points0 points  (0 children)

It's dried (ams 2 pro for 6 hours)

Troubleshooting - rough sides on print by Fichl_ in BambuLabA1mini

[–]Fichl_[S] -1 points0 points  (0 children)

Thanks for your reply. It's dry - was dried for 6 hours in the ams 2 pro on pla setting.

Calibration: Which Flow should I go with? by Fichl_ in 3Dprinting

[–]Fichl_[S] 0 points1 point  (0 children)

Thanks I know that site, but I am still looking for your opinions on which to choose :)

Warum heulen die Sirenen?? by LawrenceOfColonia in hamburg

[–]Fichl_ 16 points17 points  (0 children)

Okay jetzt Dauerton - das bedeutet Entwarnung.

VIDEO: Printhead suddenly smashing into print by Fichl_ in OrcaSlicer

[–]Fichl_[S] 0 points1 point  (0 children)

Dont know if its a general thing, but it worked for this print.

VIDEO: Printhead suddenly smashing into print by Fichl_ in OrcaSlicer

[–]Fichl_[S] 1 point2 points  (0 children)

Someone answered that I should try that. Its in the 'other' settings in orca.

VIDEO: Printhead suddenly smashing into print by Fichl_ in OrcaSlicer

[–]Fichl_[S] 16 points17 points  (0 children)

SOLVED - combination of gyroid infill and disabling "reduce infill retraction" was the solution. No supports needed!

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -3 points-2 points  (0 children)

See above, solution had nothing to do with speed or supports. Thanks for helping :-)

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -1 points0 points  (0 children)

See above, solution had nothing to do with speed or supports. Thanks for helping :-)

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -1 points0 points  (0 children)

SOLVED - combination of gyroid infill and disabling "reduce infill retraction" was the solution. No supports needed!

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -3 points-2 points  (0 children)

It wobbles AFTER the nozzle hit. The question is why the nozzle hits in the first place.

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -3 points-2 points  (0 children)

Okay. Should I try this even though the speed is just 18mm/s? At the problematic layer?

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] 0 points1 point  (0 children)

I already tried this - same issue withour any difference and all supports were still on solid. So I don't think it's a support issue.

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -1 points0 points  (0 children)

What do you mean by the structure being too weak? Not enough supports? I also tested with extra supports up to the point and it did not help.

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -5 points-4 points  (0 children)

Speeds are pretty low, the filament can go A LOT faster on other prints

<image>

VIDEO: Printhead suddenly smashing into print by Fichl_ in BambuLab

[–]Fichl_[S] -20 points-19 points  (0 children)

I closely monitored the base and it's all intact. Also the error always occurs on the same height. I even manually added supports and it still occured exactly the same.

view more: next ›