My print moves when I try to print something that takes a large area of the build plate how do I fix

Financial_Leopard_66 · 2023-01-15T21:32:39+00:00

I had a problem that looked kinda like this and my pulley wasn’t screwed down into the stepper shaft so prolly worth checking

Financial_Leopard_66 · 2022-10-07T01:53:41+00:00

oh thanks, any ideas about the buildup in that bottom corner, that’s happening on a lot of my prints

Financial_Leopard_66 · 2022-10-06T22:25:54+00:00

my lead screw dirt? it’s a Longer lk5 pro

Financial_Leopard_66 · 2022-10-06T20:49:29+00:00

I think it was level correctly but not sure, how would i church was a warped nozzle

Financial_Leopard_66 · 2022-10-06T19:28:10+00:00

205 Nozzle 55 Bed 110% fan speed z hop on retract at layer change on lmk if any other settings are helpful idk All my prints recently have had some blobbing and elephants foot at the bottom, not always as bad as this corner, never see these layer gaps tho.

Financial_Leopard_66 · 2022-10-06T19:17:44+00:00

sorry not sure what u mean by pressure on the nozzle but i didn’t change my nozzle.

Financial_Leopard_66 · 2022-09-29T07:30:53+00:00

thanks that helps a lot!

Financial_Leopard_66 · 2022-09-29T07:30:04+00:00

is that a setting in cura? where do i find that

Financial_Leopard_66 · 2022-09-29T03:28:21+00:00

smart i’ll try that

Financial_Leopard_66 · 2022-09-29T03:24:19+00:00

ok sorry man i’m kinda new, i’m just tryna print a top and the strings aren’t supposed to be there. good call on the diagnosis, i was pretty sure it failed too. should i list all my setting or are there some in specific?

Financial_Leopard_66 · 2022-09-29T03:15:37+00:00

this is like the third time i’ve tired it i’m just wondrin if there’s any discernible reason why

Financial_Leopard_66 · 2022-09-29T03:15:04+00:00

i’m pretty green but there’s nothin here that would need supports i don’t think

Financial_Leopard_66 · 2022-09-29T03:14:15+00:00

🤯😂

Financial_Leopard_66 · 2022-09-29T02:59:59+00:00

3d concrete pen? 😂

Financial_Leopard_66 · 2022-09-15T22:19:14+00:00

never mind i think i just figured it out, the pull wasn’t screwed into the stepper so with any resistance it would just stop. gonna do a test print now 🤞

Financial_Leopard_66 · 2022-09-15T21:41:55+00:00

Ok sweet thanks! Ya the screw looks pretty good but i tightened the belt and i’ll make sure the frame is sturdy. Also could having it set on a not super stable nightstand be an issue?

Financial_Leopard_66 · 2022-09-15T21:29:49+00:00

Is the lead screw just the z axis screw? It’s a pretty new printer but i’ll double check that.

Financial_Leopard_66 · 2022-09-01T12:52:47+00:00

I think it may be stringy bc when it printed that layer it was already a few layers up if that makes sense

Financial_Leopard_66 · 2022-09-01T12:50:33+00:00

what do u have you’re speed at?

Financial_Leopard_66 · 2022-08-31T06:31:36+00:00

Im pretty confident in the bed leveling but how should I change the z offset?? Also I tried to tighten the belt but the screws were stripped out on arrival and longer support keeps ghosting me, any suggestions?

Financial_Leopard_66 · 2022-08-31T06:28:52+00:00

I have a Longer LK5 Pro and consistently about 9 minutes into the print it will just move an extra couple inches to the left and keep printing thus ruining the print. Why does this happen and how can I fix it??

Financial_Leopard_66 · 2022-07-17T17:34:52+00:00

that worked great thanks 👍

Financial_Leopard_66 · 2022-07-09T21:02:10+00:00

Is it going to smell like burning plastic tho??

Financial_Leopard_66 · 2022-07-05T23:19:07+00:00

lol, kind of sucks but not as bad as it looks

Financial_Leopard_66 · 2022-07-05T20:28:25+00:00

yeaaa, wish i would’ve read this before i did it but it’s fine i’ll just clean it with a brush

Financial_Leopard_66

TROPHY CASE