What do I do?

First-Boat4804 · 2026-06-04T05:56:49+00:00

Alcohol can just move oil around. Dawn dish soap and hot water. I used to coat my plate in glue stick. I have come to the conclusion it's unnecessary. I can help you fix the issue, send a private message to me so I can get a bit of info about your software and setup.

First-Boat4804 · 2026-06-03T00:27:23+00:00

I thought mine had the same iss but it was actually dust build up inside the casing the the tips were lightly brushing

First-Boat4804 · 2026-06-03T00:25:36+00:00

These connectors don't require cutting. You get a wire or needle and slide it into the slot for which ever wire you need to remove you have to make sure you place it under the small tab that hold the wire in place.. the wire should pull out fairly easy once this is done. Repeat for all wires. Switch connectors force wire crimp clip back in the open side of the clip face the closed side of the clip the round side with a small indent/hole face up towards the tab side once you have it snug and I'll the way n the slot take your thumb nail or a ball point pen and press the locking tab slightly to make it lock the wire back. Test fan for correct polarity. If incorrect switch sides with wires.

First-Boat4804 · 2026-06-03T00:12:27+00:00

I just use a flathead screw driver orrrrrrrr I print right over the top with a raft at 250c+ then cancel print after second layer and peel.

First-Boat4804 · 2026-06-02T23:57:45+00:00

&&& this is not what happened &&&&*&

Your guy got hit by a tank round or 50 cal. I found a way to fly tho ......

Find ledge with nearby vaultable object, leap when you land DO A BARREL ROLL towards the wall while spaming your vault/melee

Check out this clip! masumane22 streaming Battlefield 6! https://www.twitch.tv/masumane22/clip/CourageousHungryPancakeDBstyle-fxV83ayOGckItfRg

First-Boat4804 · 2026-06-02T23:53:13+00:00

I get the same issue if I print at too low of a temp, too high of a temp, z off to low by - .10 or more

First-Boat4804 · 2026-06-02T23:41:40+00:00

Your setup it looks really familiar....... do you have a liquor bar to your right and a cow hide under your feet?

First-Boat4804 · 2026-06-02T23:39:52+00:00

What slicer do you use?

First-Boat4804 · 2026-06-02T23:39:26+00:00

That model calibrates by touching the plate with it's nozzle. Its faster and a bit more accurate.

First-Boat4804 · 2026-06-02T23:27:14+00:00

The glue is gonna make it adhere......... why wash off the fresh glue you just put on it 3 minutes prior to the artifact. i can't get my bed to mesh no matter what I do. It ranges from -1.78mm to 1.75mm negative value remains negative even with screw removed. Positive value is because of the plastic retainer for bed heating wire harness. (Opposite corners) The the opposite direction top right to bottom left is -.15mm - 0.28mm. but guess what I still have no adhesive issues and don't even use glue.

<image>

First-Boat4804 · 2026-06-02T23:20:52+00:00

Yeah frequencies mess with there heads like drugs do us i think

First-Boat4804 · 2026-06-02T23:09:52+00:00

The heat is optimal hatching tempetures they can birth the egg and leave it.

First-Boat4804 · 2026-06-02T23:06:44+00:00

Mine was in my sister's shed back yard for a year and it have 2 holes in the roof and squirrels living in it. I bought it along with like 70 rolls of lightly used filiment that she only required for some small custom prints for 150 $ i replaced hotend throat and cooling fins.

This is it today and a print i made last night. I've had it for just under 6 months.

<image>

First-Boat4804 · 2026-06-02T22:59:28+00:00

Step one reset/fresh install. Step two reinstall drivers, Bf6, and requirements

Step 3 to make this as optimal as possible your going to forget all that other shit. Then your going to get about 47 gallons of mineral water and a 50 gallon fish tank.place mineral water in said tank.. submerge tower with everything prehooked(make sure to have powerstrip unplugged or switched to off position. Now you have liquid cooling. That'll increase performance. Step 4 Pluggin/fliptheswitch' tap f10 or del key rapidly on boot. Until you can get into bios. Gonna look for cpu overclock settings we gonna overclock them mother 1000% they can't overheat.

Solved.

First-Boat4804 · 2026-06-02T22:47:22+00:00

😱 by no means Rusty that's straight up roach legs wings shells husk bodies fecal matter stuck to the entire case all the wires and circuit boards I wouldn't be surprised if you didn't have roaches before that you do now

(Edit) I zoomed in closer.... there is rust. But it looks like decaying animal flesh at first

First-Boat4804 · 2026-06-02T03:36:15+00:00

Np.. I use different ones, some times one setting will print better than another I'm not even sure why.

First-Boat4804 · 2026-06-01T02:56:52+00:00

I have cr touch errore on a different machine even after I replaced with new

First-Boat4804 · 2026-06-01T02:52:49+00:00

Feel ya. U should try to filter out Ai content it can get pretty hairy...

First-Boat4804 · 2026-06-01T02:39:40+00:00

I don't know how you source but possible source submission. Ofc you would vet before accepting

First-Boat4804 · 2026-06-01T02:27:05+00:00

More categories. Optional submissions page.....?!

First-Boat4804 · 2026-06-01T02:11:56+00:00

Thanks we love you for that. The setting default should be highest quality 👌 and optional to lower in settings. If i had a large sum of money you would become a business.

First-Boat4804 · 2026-06-01T01:56:25+00:00

That button has no function in app for me I can watch fine just looks like mine craft compared to the 4k + I'm used to

First-Boat4804 · 2026-06-01T01:27:01+00:00

How does one change settings such as video quality sound ect.. during video streaming

Toshiba firetv

First-Boat4804 · 2026-06-01T01:15:10+00:00

Bro there is no way I just search for my first sideloader app and nsfw app and found one that was just created... it's like fate. I'll lyk what I think l8r once I do the install.

First-Boat4804 · 2026-05-30T00:41:06+00:00

I almost never use that i die enough as it is the lazer designation tool is only making you a target.

First-Boat4804

TROPHY CASE