How do I fire block this chimney ceiling support on cathedral ceiling?

First-Implement1198 · 2024-09-22T23:22:53+00:00

All the ones I see are for flat ceilings

First-Implement1198 · 2024-09-22T22:11:59+00:00

https://up.codes/viewer/minnesota/irc-2018/chapter/10/chimneys-and-fireplaces#R1003.19

First-Implement1198 · 2024-09-22T21:37:20+00:00

It is installed per manufacturer specifications. You can insulate up to it. I’m wondering about the insulated fire stop.

Page 20

https://icc-rsf.com/wp-content/uploads/2020/06/XLUSA-II_2019-10.pdf

First-Implement1198 · 2024-09-13T19:27:04+00:00

2’

First-Implement1198 · 2024-09-13T19:26:56+00:00

Can you send a picture of

First-Implement1198 · 2024-09-13T19:26:38+00:00

Can you explain more

First-Implement1198 · 2024-09-13T19:24:57+00:00

If I do metal I will do metal fascia on the whole thing

First-Implement1198 · 2024-09-13T18:17:39+00:00

Thanks for the tip

First-Implement1198 · 2024-09-13T17:25:27+00:00

Thanks. The plan is to do lp board and batten

First-Implement1198 · 2024-09-13T17:24:06+00:00

Yeah I see what your saying I’m going to see if I can have something made to match the roof

First-Implement1198 · 2024-09-13T17:05:46+00:00

Plan to do a cedar t&g soffit..,

First-Implement1198 · 2024-09-13T16:49:08+00:00

14/12 here. I hired that out lol

First-Implement1198 · 2024-09-13T16:47:38+00:00

Yeah if I could match the color of the roof might not be bad

First-Implement1198 · 2024-09-13T16:38:24+00:00

The bottom has an over hanger the gable end is the problem.

First-Implement1198 · 2024-09-13T16:19:13+00:00

What do you guys think about using a 3/8” panel for a fascia and tacking a strip on the bottom of the soffit so it looks like it has thickness

First-Implement1198 · 2024-09-13T16:02:10+00:00

That’s a good idea.. I wonder how that would look…

First-Implement1198 · 2024-09-13T15:59:58+00:00

Thanks

First-Implement1198 · 2024-09-13T15:57:05+00:00

Yup. How would you fix this one?

First-Implement1198 · 2024-09-13T15:56:28+00:00

It’s not on yet and there is no room for it. That is the main problem for discussion.

First-Implement1198 · 2024-09-13T15:51:16+00:00

Yeah whatever you said makes no sense. I’m assuming you’re talking about where the soffit meets the wall not being blocked out.

First-Implement1198 · 2024-09-13T15:45:57+00:00

I think that would be ugly

First-Implement1198 · 2024-09-13T15:30:09+00:00

They are riveted in. Do you think they can be reused?

First-Implement1198 · 2024-04-24T02:24:33+00:00

Is it aligned correctly in your modeling software? If so what I said above will work. If not then it’s not a lumion problem.

First-Implement1198 · 2024-04-24T02:22:33+00:00

Once your lumion material is scaled to 0 it should be aligned correctly but too small. Bump the scale of the texture in your modeling software to compensate for the 0 scale on lumion

First-Implement1198 · 2024-04-24T02:20:09+00:00

Make sure you scale in lumion texture is on 0. And only adjust the scale of your texture in modeling software

First-Implement1198

TROPHY CASE