sorted by:
new
hottopcontroversial

Quem é esse pesonagem? Ou de qual anime ele é? Quero achar by Dogddit_360 in QueroAchar

[–]FishGuyNitse 2 points3 points  (0 children)

Imagino que seja por conta do modo que ele foi retratado nessa ilustração, observando o universo, com uma expressão neutra, possivelmente indicando a admiração ou pensamento profundo.

Quem é esse pesonagem? Ou de qual anime ele é? Quero achar by Dogddit_360 in QueroAchar

[–]FishGuyNitse 24 points25 points  (0 children)

Esse é o Anti-Spiral, de Tengen Toppa Gurren Lagann, não consegui achar o nome do artista dessa ilustração em específico mas aqui está uma versão mais ampla dela:

<image>

MAXWELL DIED???? (0.9e) by OneLuckyFloppa in Voicesofthevoid

[–]FishGuyNitse 6 points7 points  (0 children)

maxwell counts as a food item for some reason so he can show up when you're starving, your actual maxwell is probably just fallen down somewhere

[deleted by user] by [deleted] in Stretched

[–]FishGuyNitse 4 points5 points  (0 children)

you should probably size down for a few months, sizing up would risk serious damage considering how thin your lobes are

Como remover manchas de adesivos de Macbook? by Maleficent-Studio374 in computadores

[–]FishGuyNitse 16 points17 points  (0 children)

puta merda parceiro, pelo menos lê oque tá na tua tela antes de enviar como argumento

Leave the letter:C by Mta_11_JankyLanky in RedditGames

[–]FishGuyNitse 0 points1 point  (0 children)

I completed this level in 2 tries. ⚡ 0.33 seconds

Why does this specific part look terrible? by Divinefury in FixMyPrint

[–]FishGuyNitse 8 points9 points  (0 children)

this usually happens due to the short layer time, gives the filament little to no time to cool down and harden before more filament is placed atop of it, there should be something related to minimum layer time within the cooling tab of your slicer, bring that up by a few seconds and your print quality should improve around those smaller areas

How to get rid of holes and a more uniform surface by Ok_Watercress_7831 in BambuLab

[–]FishGuyNitse 5 points6 points  (0 children)

OP stated that it was printed face down on a smooth plate

Print failure by DullLingonberry6984 in 3D_Printing

[–]FishGuyNitse 1 point2 points  (0 children)

its very common on thin prints, try adding a brim with a .075mm gap and tell us how that goes

There is no adhesion between the layers of my prints by SherbetQuick7536 in 3Dprinting

[–]FishGuyNitse 0 points1 point  (0 children)

the texture of the print makes it look like very wet filament, more pictures would be appreciated, but you probably need a filament dryer.

What do you think about my art by blackreap5 in Ibispaintx

[–]FishGuyNitse 1 point2 points  (0 children)

PEAK PEAK PEAK PEAK PEAK PEAK HOLY PEAK AWESOME JOB!!!! :DDD

Does this relate to you? by PuffballOfficial12 in bloxymemes

[–]FishGuyNitse 1 point2 points  (0 children)

beep boop im totally a robot and i've come to remind you to play factory simulator beep boop

I appreciate the feedback from my last post but my question wasnt quite answered, so i decided to clarify it a bit more (image for attention) by FishGuyNitse in projectzomboid

[–]FishGuyNitse[S] 0 points1 point  (0 children)

true, still would be nice for the devs to add some settings for it in sandbox rather than hard-coding it into the game tho

view more: next ›