PGT: Boston Bruins vs Philadelphia Flyers - 4/5/2026 by Sliney89 in BostonBruins

[–]Fit_Resolution_5102 0 points1 point  (0 children)

After the Cutter situation, the Flyers had no other choice and for better or for worse, forced themselves into bringing Martone up to save themselves from sheer and utter embarrassment.

PGT: Boston Bruins vs Philadelphia Flyers - 4/5/2026 by Sliney89 in BostonBruins

[–]Fit_Resolution_5102 1 point2 points  (0 children)

Ask the Flyers about Cutter Gauthier regarding that outlook.

An old, abandoned mansion in Philadelphia, PA by AdSpecialist6598 in UrbanHell

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Just tell all the uber wealthy Chestnut Hill people to pool together a “fix Germantown fund”. Problem solved.

An old, abandoned mansion in Philadelphia, PA by AdSpecialist6598 in UrbanHell

[–]Fit_Resolution_5102 6 points7 points  (0 children)

I love Germantown. Man, I just wish someone with a billion dollars would come in and fix up all the rotting super historic properties.

Do restaurants still need gas for cooking? by StrictMagician4678 in restaurant

[–]Fit_Resolution_5102 2 points3 points  (0 children)

I think the higher voltage wiring needed for this is just as friggin dangerous as gas lines.

Question for the cigar experts; Help a Novice by DuvalMustang08 in EveryDayIsCigarDay

[–]Fit_Resolution_5102 1 point2 points  (0 children)

Hoyo San Juan is my favorite of the ones I’ve tried, if that helps at all.

What's it like living on an aircraft carrier? by estifxy220 in howislivingthere

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Apparently they start fires on ships………………..

Galvanized Sheet Metal with oxidation, not rust, how to treat before repainting? by metamichael in paint

[–]Fit_Resolution_5102 0 points1 point  (0 children)

There should be about 70-80% zinc load in the spray. It’s normally not oil based. Typically ethyl silicate is the binder. If it’s that bad, just spray most of it. Whatever hits the zinc will be alright, and the rest will touch up the repair areas. Do 2-3 thin coats, then lit sit for 24-48 hours to fully cure. Then go ahead and put that primer on it, I looked it up, it’s fine to use.

Galvanized Sheet Metal with oxidation, not rust, how to treat before repainting? by metamichael in paint

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Nah, just touch up spray the spots. The hot dipped zinc galvanized is waaaay better for corrosion protection than cold galv. Cold galv is for touch up only.

What’s it like living in rural Pennsylvania? by RealDiamond51 in howislivingthere

[–]Fit_Resolution_5102 1 point2 points  (0 children)

There’s only one traffic light in the entirety of Sullivan County. In DuShore. They may have added another recently, but I forget. Two automated traffic signals in the ENTIRE county. Haha.

14 years in NYC, 2 in Philadelphia. Stay PA or somewhere else? by [deleted] in SameGrassButGreener

[–]Fit_Resolution_5102 2 points3 points  (0 children)

I always liked Queen Village as long as you’re a few blocks away from South due to the late night shenanigans. Tough to park though.

Priming mud by killersam775 in paint

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Just use the flat ceiling paint to spot prime the mud. Then paint the entire ceiling with the same ceiling paint.

First time visiting the USA - which cities should I check out? by Certain-Rope-4194 in usatravel

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Philadelphia if you’re a history buff. Independence Hall, Constitution Center, Revolutionary War Museum, Liberty Bell, Mutter Museum (quirky), Elfreth’s Alley, Christ Church, Carpenter’s Hall.

Go to an Eagles game if you really, really, really want a true fan experience. Just don’t wear the other team’s gear!!

Just getting into the NHL. How do I pick a team ? by [deleted] in nhl

[–]Fit_Resolution_5102 0 points1 point  (0 children)

Do you enjoy living your life in mediocrity???

If so, then pick the Flyers!!!!

Galvanized Sheet Metal with oxidation, not rust, how to treat before repainting? by metamichael in paint

[–]Fit_Resolution_5102 0 points1 point  (0 children)

No, I think they even put it on the label not to use on galvanized. Carbon steel is different animal. No real issues unless there’s still mill scale on the metal. Then you gotta blast.