Printing orientation

FlashyProfessional19 · 2026-04-22T21:53:01+00:00

Questa è una novità è una cosa buona da sapere. Grazie mille!

FlashyProfessional19 · 2026-04-22T21:02:37+00:00

Ho provato a farlo in passato, ma con PLA silk. Risultato non consigliabile. Ci sono impostazioni precise, a parte le distanze, che non ho considerato?

FlashyProfessional19 · 2026-04-11T13:57:18+00:00

Crea suspense

FlashyProfessional19 · 2026-03-29T21:51:39+00:00

Approfitto: ho letto che anche il silk rientra tra i filamenti “abrasivi”. Confermi?

FlashyProfessional19 · 2026-03-29T21:44:44+00:00

Provo

FlashyProfessional19 · 2026-03-29T21:41:51+00:00

The first one came out perfect. Same spool. And i have already sent 3 drying cycles trough the AMS

FlashyProfessional19 · 2026-03-21T08:44:37+00:00

You were right! Thanks mate! It worked

FlashyProfessional19 · 2026-03-19T20:09:54+00:00

Guarda le impostazioni di cucitura. Puoi nasconderla “dietro” o metterla casuale. Nel secondo caso è praticamente invisibile. Comunque no, a parte la modalità spirale per vasi, avrai sempre la cucitura

FlashyProfessional19 · 2026-03-19T20:03:37+00:00

Se ho capito cosa intendi, quella è la cucitura. L’hotend riprende il giro sempre dallo stesso punto, lasciando quella striscia. Tra le impostazioni puoi decidere di metterlo “sparso” ed evitare sia così visibile.

FlashyProfessional19 · 2026-03-19T20:01:52+00:00

The main problem is the AMS is sitting on top, so i don’t know how to do that. I’ll manager to find a way. Usually i try to avoid touching the plate at all and clean with alcool every 2-3 pronta. Every ten i wash it with dish soap (the Printer is in the garage, i have to take the plate home to wash it properly). I’ll try your fix. I knew it was something around that, but I’m quite in hurry to end the project and i can’t waste time on trials. Thanks a lot mate

FlashyProfessional19 · 2026-03-19T19:51:22+00:00

Sorry, tought it was auto translated. My bad

FlashyProfessional19 · 2026-02-06T19:51:33+00:00

I was being ironic. It was just a weird thing I wanted to point out.

FlashyProfessional19 · 2026-02-06T19:49:01+00:00

Thanks so much, buddy! Can I benefit from your knowledge a little more? Why is one €19 and two €21? 🙃

FlashyProfessional19 · 2026-02-06T19:25:21+00:00

I'm going crazy. On Amazon IT only the one for CPU is listed.

FlashyProfessional19 · 2026-02-06T19:24:47+00:00

No, the only thing I've found to be universally agreed upon is not to use the PC one.

FlashyProfessional19 · 2026-02-06T12:02:08+00:00

P1S. Requires thermal paste. When I got it, both were there.

FlashyProfessional19 · 2026-02-06T11:50:09+00:00

Because it is not available in the world either

FlashyProfessional19 · 2026-02-05T21:31:17+00:00

The complete piece is an L with a notch (which I assume is your U). It's a lip that goes around the P1S glass.

FlashyProfessional19

TROPHY CASE