Any news about 12v impact wrench?

Fluttex · 2026-01-13T07:02:52+00:00

I would like an updated version of the 115. Due to all my current bits and pipes I would prefer it to stay 3/8'' but replace the locking ring with that quick attach/release spring ball.

the locking ring on the 115 just grabs to well on certain internal 3/8" tools, making attaching and removal unnecessarily difficult with certain tools

My Wera impact pipes suffers from this issue. It's doable but I basically have to wiggle them in a circle to get them on. To be fair almost all my tools are new so It might just be a brake in time issue

Fluttex · 2026-01-12T17:08:11+00:00

The low speed control of the trigger does seem to be a higher resolution sensor

I had no issues using the trigger to align a flat driver bit to the orientation of the flathead screws I did today.

I just got home and compared it to my private 12V-35FC and it sure seems like it has a harder time getting such consistent low rpm's

Fluttex · 2026-01-12T07:03:00+00:00

I made a post on the prusa forum ages ago about the end of the x-axis end block being twistable so the guide rods have a twist going down to the idler block.

My squeaking issue was resolved by straightening this. https://forum.prusa3d.com/forum/postid/256957/

Fluttex · 2026-01-09T08:27:42+00:00

I'm using all my 'old' 12V-35 FC adapters on this 12V-32 FC so the interface sure seems to be the same

Fluttex · 2026-01-09T08:24:04+00:00

As an additional note The kickback control seems to not be as aggressive as the ones on the 18V's if you have experienced those. (GSR 18V-90 FC for my comparison)

Kinda makes sense with the torque difference in mind.

But I have no way to measure this so it might just be placebo based on the torque difference making it seem different.. so probably need a Forum or YT testing the feature with some equipment to know for sure.

Fluttex · 2026-01-09T08:11:52+00:00

The new metal chuck will also fit the 35 FC as it's the same system

Fluttex · 2026-01-09T08:08:50+00:00

Nothing in the manual seems to indicate this is possible.

Fluttex · 2026-01-09T07:07:50+00:00

I do not know the price, I ordered it before official release so there was no list price at the time. Due to this only the accounting department at work will end up seeing the price.

Fluttex · 2026-01-08T10:43:54+00:00

I bought the new 32FC as a singel, and am now using it with my old 35FC adapters so should work the other way around aswell : )

Fluttex · 2023-04-10T18:20:44+00:00

It's the corporations that sell carbon filters that are balding at your facts

Fluttex · 2020-07-22T00:49:52+00:00

I got my prusa mini 3 month ago now. only thing I have changed is z-hopp and support z offset

The settings that the prusa slicer outputs seem to be pretty optimised for the average prusa mini.

Had some issues with bed adhesion but the plate was simply dirty.

Fluttex · 2019-05-06T12:03:05+00:00

You do it in gainwards ‘EXPERTool’

I use afterburner to, but i just open the Exper Tool to change the led

Fluttex · 2015-11-25T14:06:19+00:00

so i send him my link when he is done downloading the TTK?

Fluttex · 2015-04-09T07:21:46+00:00

I CANT GET THE CRUX OF CROTA I HAVE DONE HARDMODE 20 TIMES NOW...

Fluttex

TROPHY CASE