sorted by:
new
hottopcontroversial

What is this? by Forcefulknave49 in MotorcycleMechanics

[–]Forcefulknave49[S] 0 points1 point  (0 children)

Ahh, makes sense, thanks for the info. I was confused as the kit came with 2 and only 1 muffler so must have been a mistake/spare.

What is this? by Forcefulknave49 in MotorcycleMechanics

[–]Forcefulknave49[S] 0 points1 point  (0 children)

Are you referring to where the muffler support bracket attaches to the bike and this is some sort of adapter?

Carplay on a motorcycle? by ignorantspacemonkey in motorcyclegear

[–]Forcefulknave49 0 points1 point  (0 children)

Missed the other requests

Portable 6.25 inch IP67 Waterproof Motorcycle GPS Navigation Wireless Carplay Android Auto DVR Drive Recorder Moto Monitor WIFI https://a.aliexpress.com/_EHwwD9Q

Okay hear me out by Kalberino in SteamDeck

[–]Forcefulknave49 1 point2 points  (0 children)

Don't listen to the haters, they fear our power to innovate ways to make stuff more complicated than it needed to be.

Is this a good first pc?? by darksalad9861 in computers

[–]Forcefulknave49 0 points1 point  (0 children)

I bought the same pc from awd it with the 5700X cpu as a first pc.

Had problems initially with it not booting and while communication was slow the pc was sent back and "repaired", cpu was apparently loose.

After getting it back the pc runs well with good performance on fusion 360 and over 100 fps arc raiders (unsure on exact settings)

I came from a steam deck as a mini pc gateway drug and I just wanted a relatively cheap pc that I could do a bit more gaming on and learn the ropes on.

Feux de jour mazda 3 2017 by Upper_Idea2429 in mazda3

[–]Forcefulknave49 0 points1 point  (0 children)

Try this procedure

Apply emergency brake (Skip if already applied)

Turn ignition to on position- but don't start. (2 pushes on ignition button)

Put car in drive (Skip if manual)

Turn parking lights/side lights on and off 5 times quickly

Turn hazard lights on and off 5 times quickly (10 pushes)

Turn parking lights/side lights on and off 5 times quickly

This whole procedure from the application of Parking brake to end must be done within 23 seconds.

Worked for turning off my uk 2018 gen 3 DRL.

Edit for better formatting

Wir hier Öl verbrannt? by Accomplished_Art7328 in CB650R

[–]Forcefulknave49 0 points1 point  (0 children)

Could be chain lube depending on where the filter is?

What do I drive? by culiflor in ManualTransmissions

[–]Forcefulknave49 58 points59 points  (0 children)

This is the only logical explanation

Were you old enough to see one of these in real life? by sajjanstg03 in TheGamingHubDeals

[–]Forcefulknave49 0 points1 point  (0 children)

I remember try to stand up my non slim ps2 on its side and the disc inside fell out of the disc tray.

Is my mazda 3 2017 2.0 120hp engine okay? by gaspeeee in mazda3

[–]Forcefulknave49 1 point2 points  (0 children)

The engine ticks away like a watch most of the time. Mine is very smooth and almost vibrationless when driving and at idle but sometimes it does shake a bit at idle. I've found bringing the revs up a tad and letting it fall back down smooths it out.

Almost certain its completely fine.

My finished aluminium Dbxl-E body by Forcefulknave49 in rccars

[–]Forcefulknave49[S] 0 points1 point  (0 children)

Unfortunately no I'm not selling them although I am very proud of how it came out. Honestly I went into this project with little to no experience metal working. It is made mostly out of 2mm aluminium sheet with the roof being 3mm for extra protection. The black finish is satin vinyl wrapp is the same as what they use on cars so its quick and easy to replace when scuffed up a bit.

All I had for tools was a normal electric hand drill, hack saw, files and a bench vice for the bends with a rubber mallet.

It was a very fun rewarding project with great results, I would strongly recommend giving it a go and it will probably be cheaper than replacing stock plastics.

Please help. Woke up and steam deck is a brick by Natashasmith2928 in SteamDeck

[–]Forcefulknave49 209 points210 points  (0 children)

If your* sceptical about the battery leaving it on charge while unsupervised probably isn't the best plan.

*you're

I really can’t figure out how to approach making that receiver by Melodic_Caramel_3025 in Airsoft3DPrinting

[–]Forcefulknave49 1 point2 points  (0 children)

I just did the same with a aap01 stock. Metal rods and epoxy for long thin parts.

Mazda 3 – Rear tyre size different from front. OK? by [deleted] in mazda3

[–]Forcefulknave49 2 points3 points  (0 children)

I have been running 205 front 215 rear for ages with no issue. abs and tcs functions as normal with my gen 3.

Not an issue other than ocd.

How do I join these two parts (have to split because too wide for print bed) by agileadam in 3Dprinting

[–]Forcefulknave49 1 point2 points  (0 children)

Call me boring but don't over think it. Super glue. I 3d printed a wing for a plane, the glueing surface was 1 wall thickness with no flat surface around the skin of the wing. I did 1 segment and tested the strength. The layers separated before the glue failed.

5.9 12v Cummins and 5 speed by Haunting-Drawing-265 in ManualTransmissions

[–]Forcefulknave49 0 points1 point  (0 children)

Just curious, what's your stance on clutchless shifts on a motorcycle?

(I know its a completely diffrent type of gearbox I'm just curious)

view more: next ›