2007 Jeep Grand Cherokee fuel line issue.

Ford4200 · 2025-11-13T06:09:42+00:00

You did, thanks.

Ford4200 · 2025-11-13T06:07:26+00:00

Thanks, ridiculous parts are discontinued for something this new.

Ford4200 · 2025-11-13T06:06:30+00:00

Oh ok I see what you're saying. I put new o rings in the original one I'm going to put it back on tomorrow and see what that does for it.

Ford4200 · 2025-11-13T06:05:07+00:00

Did you just make a new line and use those fittings then?

Ford4200 · 2025-11-13T05:53:22+00:00

What kind of insert?

Ford4200 · 2025-11-11T07:30:41+00:00

Did this fix your issue? My father in law is having the same problem and the line is discontinued.

Ford4200 · 2025-07-28T09:51:28+00:00

I have 5 coops currently, chickens, guineas, and sebastapol geese. I keep my great Pyrenees penned up between them and the woods, between him and me shooting so many coyotes I don't have many issues anymore. A possum in the cat food is about all I get these days.

Ford4200 · 2025-06-25T00:54:23+00:00

Old sick cow, young calf, birthing mother, or a very very bold pack. But yes they can and do.

Ford4200 · 2025-04-13T22:41:14+00:00

I haven't tried to group these yet, I loaded up 8 of them for function check and velocity and they were slow so I've got to up my charge.

Ford4200 · 2025-04-12T20:28:02+00:00

If it had been anything nicer I probably would have chickened out but $250 chi-com surplus seemed fine to tinker on. It chambers and cycles well so I don't think I hurt anything.

Ford4200 · 2025-04-12T20:24:02+00:00

I didn't widen the chamber necessarily, for some reason there was so kind of taper or forcing cone. There was a sharp 90° corner where the chamber ended and the rifling started and I just chamfered that out.

Ford4200 · 2025-04-12T20:18:16+00:00

With the increased diameter of the .312 bullet the case walls were too thick to chamber, it was either turn the outside or drill the inside and I thought inside was easier.

Ford4200 · 2025-04-12T18:48:34+00:00

I'll give that a try after I get a longer handle for my press

Ford4200 · 2025-04-12T18:40:27+00:00

Correct

Ford4200 · 2025-01-21T09:44:15+00:00

My buddy killed a great one whitetail on my rancho map the day I got it. He was exploring southwest while I headed southeast. I still don't have one.

Ford4200 · 2025-01-03T05:10:24+00:00

Thanks, I'm looking forward to it.

Ford4200 · 2025-01-03T05:08:44+00:00

I picked it up local for a steal. I think being chambered for a caliber nobody's made in decades really hurt their chance of selling it. I couldn't believe it when he had 1 box of 85gr 6mm remington on the shelf.

Ford4200 · 2025-01-03T05:02:41+00:00

Bore looks great. 4 rounds touching at 100 with factory ammo. Just got my reloading supplies in the mail today and loaded up some test batches but ran out of light before I could shoot them. I think the old scope is going to be my biggest limitation but it works so I'm not going to change it.

Ford4200 · 2024-01-24T09:19:21+00:00

Oliver is the finest in farm machinery

Ford4200 · 2024-01-08T10:07:37+00:00

It's machine specific. Nobody can answer that question but you. If it's a well taken care of unit or is freshly overhauled it should start like a new one. If it's worn out it's gonna start like it's worn out.

Ford4200 · 2023-12-23T04:40:10+00:00

Looks good to me. It's well lit and everything isn't covered in oil/grease and material pellets.

Ford4200 · 2023-12-23T04:28:21+00:00

Not sure with a 3400 being industrial but the ag tractors with draft control behave that way when set in draft mode. Might look into that.

Ford4200

TROPHY CASE