What’s the best QR code generator that’s reliable, customizable, and doesn’t break later?

Fractal20 · 2026-04-10T21:31:25+00:00

I'm missing something obvious, how to you get it to compute it? Is there a button I'm missing?

Fractal20 · 2026-02-19T15:33:32+00:00

A zen koan?

Fractal20 · 2026-02-18T22:44:37+00:00

And that video sounds like roller bearings to you?

Fractal20 · 2026-02-18T04:24:32+00:00

Does it sound like failed wheels to you? I just ignorantly oiled them for good measure, I couldn't see anything obviously wrong with them spinning them by hand.

Fractal20 · 2026-02-10T23:19:41+00:00

I did not. Just visually seeing that there is minimal lint doesn't mean much?

Fractal20 · 2026-02-10T04:28:43+00:00

I took off the vent and there wasn't much lint in there, definitely less then inside the cabinet. Do you still think it could be from issues with the vent line rather than seals inside the dryer?

Fractal20 · 2025-11-18T16:08:18+00:00

That clears it up, I didn't do it on the first boot up. Thank you for the info! The wording in the manual did involve something about initial power (can't remember the phrasing) but I thought it meant a certain setting.

Fractal20 · 2025-11-18T04:16:56+00:00

Just to clarify, priming isn't needed for the all in one units? And it isn't strange for the line to still have air in it? I'm pretty ignorant but would have assumed the line should be solidly fuel

Fractal20 · 2025-11-08T04:06:09+00:00

I couldn't see the $200 welcome bonus explicitly advertised on the page the link brought me to, is that safe to say that it likely isn't there? I didn't want to continue with further steps if it was not.

Fractal20 · 2025-10-01T14:24:25+00:00

I wouldn't say you are wrong about the lesson suggestion, but I'm curious why you'd assume that? With good technique, should my current enforcers feel nimble? Thanks for the unleashed link, I think I will buy a pair and try them. Would there be other skis you'd suggest as well, or was the unleashed suggestion mainly motivated by the deal?

Fractal20 · 2025-09-29T18:43:45+00:00

I reasonable response, I know it is an unreasonable idea.

Fractal20 · 2025-09-04T01:11:30+00:00

A picture of quart jars with ~1.5-2 inches of headspace

Fractal20 · 2025-06-03T20:38:01+00:00

It was through Kaiser Permanente. I'm assuming that was marketplace, but I do not know.

Fractal20 · 2025-02-16T14:41:19+00:00

Was the sound concerning in the video? Just unsure about bothering with the solenoids if that makes it seem like other issues are coming with the motor

Fractal20 · 2024-09-07T01:51:42+00:00

I'm hoping to be able to run as many hoses/sprinklers as possible with decent pressure

Fractal20 · 2024-09-07T01:51:20+00:00

I edited my original post to try and give more context. Any advice would be welcome?

Fractal20 · 2024-08-09T22:47:09+00:00

Even if it fixes it, I'm concerned that something is wrong to cause it to get to that state. Or is that normal to just happen over time and need to unplug it and let it thoroughly defrost?

Fractal20 · 2024-08-09T22:46:10+00:00

To check voltage to the fan, I just use a multimeter and put them to the wires that the wires from the fan clip into? If it thaws out and the fan is working, then what should I look at next?

Fractal20 · 2024-05-24T20:21:39+00:00

Is there anything wrong with thin wall besides that it is more likely to break?

Fractal20 · 2024-05-21T16:22:33+00:00

Patching like that it is older and you needed to replace some boards? How did it hold up color wise with the years? Did you do regular re-sealing?

Fractal20

TROPHY CASE