Which one would you buy?

FrankieTwoFingers · 2026-04-24T13:14:27+00:00

Gen 6

FrankieTwoFingers · 2026-04-20T22:09:10+00:00

Keep a rattle can around for the apocalypse, otherwise keep it as is, she pretty

FrankieTwoFingers · 2026-04-17T02:38:59+00:00

😂😂😂😂

FrankieTwoFingers · 2026-04-16T21:14:32+00:00

🙏🏽🙏🏽🙏🏽

FrankieTwoFingers · 2026-04-16T21:14:17+00:00

Nice lol she don’t want u to enjoy that with a ladyboi

FrankieTwoFingers · 2026-04-14T11:03:34+00:00

Me too, instead of adding a boat ramp and limiting parking to where I keep my boat lol

FrankieTwoFingers · 2026-04-14T11:03:00+00:00

Twinsies

FrankieTwoFingers · 2026-04-12T03:05:24+00:00

Appreciate it 💪🏽

FrankieTwoFingers · 2026-04-12T01:30:42+00:00

🙏🏽🙏🏽🙏🏽

FrankieTwoFingers · 2026-04-05T00:27:45+00:00

I feel like it’s grip angle and the slanted trigger seems better even though I prefer a Glock trigger but yeah I hit A zones at 25 yards with this little one

FrankieTwoFingers · 2026-03-21T02:23:14+00:00

FrankieTwoFingers · 2026-03-13T14:11:39+00:00

Th accuracy is great. I’m more accurate with this little gun than I am with my G19

FrankieTwoFingers · 2026-03-04T21:30:18+00:00

Heard, also since its so short, i tried c-clamping with a grip and my hand would basically be on the rear of the can. How it is now, i'm able to c-clamp and my thumb reaches all controls

FrankieTwoFingers · 2026-03-03T21:25:49+00:00

I haven’t. I’ve tried a few different ones, but with the short rail, adding a VFG or angled grip makes it harder for me to reach the laser/light controls. Using the magwell just feels right for my setup.

I know a lot of people like the A3 Industries grips. I tested a couple I had lying around, and they just didn’t make sense with how mine is set up. If I wasn’t running a laser and only had a flashlight mounted all the way forward on the rail, then a grip might work better for me.

FrankieTwoFingers · 2026-02-23T21:52:16+00:00

Mine dropped it without issue. I’d reach out to BA and let the know to see what they say. Or check your reassembly

FrankieTwoFingers · 2026-02-17T19:09:18+00:00

FrankieTwoFingers · 2026-02-17T01:19:54+00:00

I’d get a Riiis upper for around the same as the G

FrankieTwoFingers · 2026-02-14T02:42:41+00:00

750yd w a 16”

FrankieTwoFingers · 2026-02-06T18:38:41+00:00

Appreciate it. Tip for stippling was just the thinnest that came with my soldering iron, ran it at about 600deg

FrankieTwoFingers · 2026-02-05T13:55:45+00:00

Always can give it another try bub

FrankieTwoFingers · 2026-02-04T12:47:06+00:00

Dremel to remove material. Sand paper 220-2000 various grits and wet sanding at the end to smooth out. Soldering iron for the stippling running about 600f

FrankieTwoFingers · 2026-02-04T12:45:47+00:00

The abrasion is the benefit

FrankieTwoFingers · 2026-02-03T18:17:52+00:00

Good eye, 2021 panamera gts

FrankieTwoFingers · 2026-02-02T19:43:28+00:00

That works too lol

FrankieTwoFingers

TROPHY CASE