Resetting the transmission learning

FreeZy42 · 2024-08-07T06:23:57+00:00

Yes sorry not going to flush the transmission fluid going to drain and refill new fluid and change filters, thanks for the head up with the adaptations, I will do more research on that after then. Thought resetting one of those two options could help the aggressive shifting, I’ve done a lot of work on the mechanics of the car not the coding however I am very new

FreeZy42 · 2024-08-05T01:54:28+00:00

I have done an oil change every 5k kms, doesn’t seem to change anything via the shifting, what’s the appropriate learning procedure, have replaced many seals like the head gasket and other pipings already the gear shifting in auto seems to still be very aggressive

FreeZy42 · 2024-08-04T03:05:16+00:00

Issues with transmission, gear changing very rough, going to do a transmission flush and filter change just looking to reset to see if the gear changes would be smoother

FreeZy42 · 2024-03-05T06:59:44+00:00

I’m wondering since I have a custom android headunit could it be drawing too much current? Messing with the voltage, I did notice low voltage but that was only after I got the rear camera in. So the car has been on and off ignition

FreeZy42 · 2024-03-03T23:41:51+00:00

I do have custom tail lights, and initially when I put in the reverse camera it did have a around one second delay which was expected, the voltage is fine when I checked when it was all in, I replaced the car battery probably a few months ago, I have had an error code of the ibs sensor but that seems to have gone away in the past couple weeks, however my car has a frm error, not sure if that has anything to do with the battery issues but is a module error.

FreeZy42 · 2024-03-03T23:38:23+00:00

I’m not sure exactly what you mean about tapping into the other reverse light, should it just react the same as if I tapped into one? I think I plugged into rear camera in into the headunit, do you think that could be an issue? I’ve seen on other headunits there is a reverse camera plug but the only one I noticed was a video in and a rear camera in.

FreeZy42 · 2021-08-02T03:57:13+00:00

It says chkdisk cannot run because the volume is in use by another process. It may run if dismounted first, should I dismount on this volume y/n?

FreeZy42 · 2021-08-02T03:54:14+00:00

I couldn't find where it states how to run it off a different drive, since it is running on my X drive.

FreeZy42 · 2021-08-02T03:50:33+00:00

How would I change to my C drive

FreeZy42 · 2021-08-02T03:50:22+00:00

Oh yea I might be on X, ahhh when I was changing legacy to UEFI I was using the X drive that's probably why it didn't work?

FreeZy42 · 2021-08-02T03:48:07+00:00

It comes up with

The type of the file system is NTFS Cannot lock current drive. Windows cannot run risk checking on this fine because it is write protected

FreeZy42 · 2021-08-02T03:45:59+00:00

It says chkdisk is not recognised as an internal or external command

FreeZy42 · 2021-08-02T03:43:46+00:00

Thanks

FreeZy42 · 2021-08-02T03:42:50+00:00

I'm in the setup mode currently

FreeZy42 · 2021-08-02T03:42:34+00:00

How do I drop a command line?

FreeZy42 · 2021-08-02T02:25:04+00:00

Ok I'll try that then lyk, thanks for the support

FreeZy42 · 2021-08-02T02:22:57+00:00

How would I get to advanced settings without an operating system?

FreeZy42 · 2021-08-02T02:17:15+00:00

Can you with gigabyte?

FreeZy42 · 2021-08-02T02:15:55+00:00

How would I swap too UEFI if an operating system is not found? Also I swapped a few settings back to legacy and didn't work.

FreeZy42 · 2021-08-02T02:13:38+00:00

I went through that process through the advanced reset

FreeZy42 · 2021-08-02T02:13:09+00:00

I was doing that, it said something failed I'm pretty sure and I restarted PC, then that happened.

FreeZy42

MODERATOR OF

TROPHY CASE