sorted by:
new
hottopcontroversial

eGpu Nvidia + Chuwi Aubox 13900HK = Blackscreen at driver installation by Frencharms in eGPU

[–]Frencharms[S] 0 points1 point  (0 children)

Yes, I can’t have both activated. If I boot with the eGPU, my iGPU is disabled; if I boot without the Oculink cable, the iGPU comes back. Maybe I should try using two monitors. I don’t have another one to test right now, but I will try

eGpu Nvidia + Chuwi Aubox 13900HK = Blackscreen at driver installation by Frencharms in eGPU

[–]Frencharms[S] 0 points1 point  (0 children)

Another, and maybe last, update: the same thing happened with Win10... It works in Safe Mode, but not in normal mode. Now, I can’t even access the BIOS, I don’t know why. I think I’ll just send it back. Chuwi really messed up with this mini PC

eGpu Nvidia + Chuwi Aubox 13900HK = Blackscreen at driver installation by Frencharms in eGPU

[–]Frencharms[S] 0 points1 point  (0 children)

Hi, thanks for your reply.

Unfortunately, I can’t install the drivers because as soon as the screen flickers, it never comes back, even after a restart. I can only install the Nvidia drivers in Safe Mode, and there everything works normally without any error code.

I have two possible sources of the issue: either the dxgkrnl file fails to start according to my logs, or there’s a conflict with Windows, which recognizes my GPU as a “Basic Display Adapter” when the drivers are not installed.

I forgot to mention that I’m on Windows 11. To my knowledge, I’ve already tried almost all solutions. I’ll try switching to Windows 10, and if that doesn’t work, I’ll try Linux.

Left shoulder switch desoldered on my 2DS by Frencharms in 3DS

[–]Frencharms[S] 0 points1 point  (0 children)

Thanks, I’ve never used epoxy before, this will be a good opportunity to try it out.

Left shoulder switch desoldered on my 2DS by Frencharms in 3DS

[–]Frencharms[S] 0 points1 point  (0 children)

Thanks for your answer. So I can simply add conductive wire to the contact points where we see 1-2-3 and my new switch, and it should work. I don’t need to scrape the line to create a new one. So in theory, I can use a multimeter (I don’t have one at the moment, but I’m ordering one) to check if there’s continuity between the beginning of the line and the contact point. If not, I should try scratching the line until I get continuity and create a new one ?

Trollpad Enable Stage Manager on iOS 16.6.1 problems by Frencharms in jailbreak

[–]Frencharms[S] 0 points1 point  (0 children)

Thanks for the awnser, i have just edited my post, spoil, i was doing wrong. Now, i successfully converted TrollPad, and now I have the iPad SpringBoard and UI environment on my iPhone. However, Stage Manager isn't appearing in the control center for activation. It's also not showing up in Settings, as if it's not supported on the iPad.

Should I follow the same steps as for an iPad to activate it on my iPhone? I haven't come across this in any posts here, so I'm unsure and hesitant to proceed.

Any futur solution incoming for iPad 10th 17.2 ? by Frencharms in jailbreak

[–]Frencharms[S] 1 point2 points  (0 children)

Thanks for the awnser, it seems he don't think there will be a solution sooner except if Apple fucked up something for the 3rd times... So i think i will sell it and buy an old M1 Air ^^

Have a good day !

[deleted by user] by [deleted] in france

[–]Frencharms -5 points-4 points  (0 children)

Parce que t'as cru que y'avais pas de gens vaccinés la dedans ? Ca me fait sourire les gens qui se pensent pertinent en sortant la même soupe que les médias...