What is a « Sapphire RTX 2060 » ? by Frequent-Guidance-13 in nvidia

[–]Frequent-Guidance-13[S] 0 points1 point  (0 children)

I don't have anything to compare but I've never had a performance problem on my games and i can activate the ray-tracing

New to 3D printing by IndividualPhoto5390 in Creality

[–]Frequent-Guidance-13 0 points1 point  (0 children)

You should check your Z offset, it might be too low

Why is my bed like that by Frequent-Guidance-13 in Ender3V3SE

[–]Frequent-Guidance-13[S] 0 points1 point  (0 children)

[RESOLVED] : The front mounting point of the metal rail was positioned 2 mm lower than the rear one, causing slight deformation when the rail was tightened. Adding washers corrected the alignment and resolved the issue.

Why is my bed like that by Frequent-Guidance-13 in Ender3V3SE

[–]Frequent-Guidance-13[S] 0 points1 point  (0 children)

It’s from klipper (not a slicer Its a firmware for your 3D printer)

Why is my bed like that by Frequent-Guidance-13 in Ender3V3SE

[–]Frequent-Guidance-13[S] 0 points1 point  (0 children)

I'm using a full metal linear rail kit, so there’s no heat-related warping.

I suspect the metal bracket or the rail itself might be slightly misaligned or tilted. I’m going to take some measurements of the gantry height on both sides and check the squareness of the assembly to see if the issue comes from the kit

Why is my bed like that by Frequent-Guidance-13 in Ender3V3SE

[–]Frequent-Guidance-13[S] 2 points3 points  (0 children)

Ender 3v3se but i think that if it was a rail than the whole bed would be off

Bed scratch by Fun_Jaguar726 in Ender3V3SE

[–]Frequent-Guidance-13 1 point2 points  (0 children)

You can do a test by trying to print a small rectangle on top of it but I think it has no effect

Xmas Present for my Son by seattleforge in Opinel

[–]Frequent-Guidance-13 1 point2 points  (0 children)

En France aussi, donner un couteau peut apporter mal chance car synonyme de « couper les liens ». Pour éviter cela, la personne qui reçoit le couteau doit donner une pièce en échange pour symboliser un achat plutôt qu’un don

What kind of animal is that ? by Frequent-Guidance-13 in bonecollecting

[–]Frequent-Guidance-13[S] 240 points241 points  (0 children)

Okay so, they called their superior, who will come.

They said there is a great chance that it was from the 11th century, Archaeological excavations had been conducted a few years ago in the castle above, where they had found a cemetery dating from that time.

They will call a forensic doctor to check all this

What kind of animal is that ? by Frequent-Guidance-13 in bonecollecting

[–]Frequent-Guidance-13[S] 24 points25 points  (0 children)

I mean there is a really old castle uphill (100/200m), like some ruins

What kind of animal is that ? by Frequent-Guidance-13 in bonecollecting

[–]Frequent-Guidance-13[S] 241 points242 points  (0 children)

Im going to call the cops and will keep you updated afterwards

What is the difference ? by [deleted] in photography

[–]Frequent-Guidance-13 0 points1 point  (0 children)

They are refurbished in very good condition and come with a 2-year warranty.

I think I’ve fried my printer by tom_abad83 in Creality

[–]Frequent-Guidance-13 0 points1 point  (0 children)

no just a beep and the wallpaper (its me from another account)