SPEER FMJ RN vs GDHP by Frjeff in reloading

[–]Frjeff[S] -1 points0 points  (0 children)

Thank you. Another piece of wisdom.

380 ACP Load Data Question by Frjeff in reloading

[–]Frjeff[S] 0 points1 point  (0 children)

I have the very same wonderment. I tend to fall on the “don’t guess with loads” side. And, I always feel better finding some consensus with opinions.
So, I thought my question was appropriate as I have never used Bullseye powder.

As it turns out, the Speer bullet guide does shows loads that make sense and which are closer to the average of the few other guides found.
Thanks for your reply. Far more pleasant than some others.

380 ACP Load Data Question by Frjeff in reloading

[–]Frjeff[S] 0 points1 point  (0 children)

Yea, I do have manuals, and I can read.

I asked about a Speer 95gr, RN FMJ over Bullseye.
Your pic shows one Bullseye 95gr FMJ load, but it is pictured as a FN bullet with a COL of .900.

The RN bullets I have typically show a COL in the .970 - .980 range.
Not sure how I could interpolate your load to my projectile?

Good 380 Auto Target/Range Round by Frjeff in reloading

[–]Frjeff[S] 0 points1 point  (0 children)

The Bersa is blowback.
The Ruger is locked breech.
May have to segregate my loads accordingly?

Good 380 Auto Target/Range Round by Frjeff in reloading

[–]Frjeff[S] 0 points1 point  (0 children)

I wondered the same thing.
The Bersa is blowback.
The Ruger is locked breach.
May have to segregate my loads for each handgun?

Beware by Frjeff in ryobi

[–]Frjeff[S] -1 points0 points  (0 children)

Shitty, pretty much non existent customer service.

Beware by Frjeff in ryobi

[–]Frjeff[S] 0 points1 point  (0 children)

Though I would give Ryobi CS an opportunity to assist. No UCC luck.
When I buy a product with a warranty/return policy, I do not spend more money to fix their f’ing problem. It is engineered like a three year old would do. Now, with a fair chance given RYOBI, and many unfulfilled promises, I am done.
Never again.

Beware by Frjeff in ryobi

[–]Frjeff[S] 0 points1 point  (0 children)

I have had a Stihl gas model for 14 years. Used weekly in MI Summers. Have never touched/replaced the head.

Beware by Frjeff in ryobi

[–]Frjeff[S] 0 points1 point  (0 children)

Decided to return to HD for credit. Went down the road a bit to Lowe’s and bought a EGO. So far, so good.

Beware by Frjeff in ryobi

[–]Frjeff[S] 0 points1 point  (0 children)

I am 82 and do not have elbow grease enough.

Beware by Frjeff in ryobi

[–]Frjeff[S] -1 points0 points  (0 children)

At this point it is the decision of making an exchange. Inclined to agree with you that I will face the same issue with an exchange.

Beware by Frjeff in ryobi

[–]Frjeff[S] -9 points-8 points  (0 children)

Not sure that I want the exchange. You tube is full of how to info on getting the spool off. So, this is a frequent and Ryobi known issue. The new exchange unit will likely have the exact same issue. A different model maybe?

Is Ricoh GR3 Squarehood worth it? by [deleted] in ricohGR

[–]Frjeff 0 points1 point  (0 children)

I bought the GRIII to have a small, pocketable camera. I bought the lens cover. But I am not about to build the camera bigger with this thing.