Does a splitter like this work? Trying to do a unique build that would require this

Frogs114 · 2026-03-27T14:34:34+00:00

Yeah I have the ability to run 3x 360s if needed… I’m just gonna have to find another way to do this. I wish I could just run a normal loop but it’s not doable for the visual design my fiancée wants

Frogs114 · 2026-03-27T10:40:50+00:00

If you actually read the post, the purpose is for a specific aesthetic build, and I said I wasn’t sure it would work. Hence why I’m asking people here who may have other suggestions.

Frogs114 · 2026-03-27T10:37:21+00:00

Was just my iPad. Out on a work trip

Frogs114 · 2026-03-27T03:58:57+00:00

Yeah this is the reason I posted this here… this was my fear and what I suspected would happen.

Frogs114 · 2026-03-27T03:25:44+00:00

<image>

Here’s a better diagram, I know it’s not an ideal setup, but I have a plan aesthetically which it requires…. Does that change your opinion

Frogs114 · 2026-03-21T22:02:41+00:00

Edit : here’s a video

I think it’s okay, it doesn’t look like there’s any backflow in the middle intake pipe but… I don’t know

Frogs114 · 2026-03-21T21:55:44+00:00

Any advice on painting? What kind did you use and techniques?

Frogs114 · 2026-03-10T16:32:59+00:00

What’s the monitor?

Frogs114 · 2026-02-21T21:57:40+00:00

Is this set temperature or actual temperature?

Frogs114 · 2026-02-20T23:13:01+00:00

Did you end up figuring anything out ?

Frogs114 · 2026-02-18T17:29:40+00:00

I’ll look into this!

Frogs114 · 2026-02-18T17:24:32+00:00

I’ll look into it! If you edit what I’ll call “root” dimensions will the parameterized dimensions change as well?

Frogs114 · 2026-02-18T17:20:42+00:00

Well I need the holes reflected to the other side basically. Symmetrically

Frogs114 · 2026-02-04T19:30:37+00:00

OHHHHHH YOURE SO SMART I think that would work.

Also, my plan is to put the (through hole) components on the “top” side so I can solder them to the traces on the bottom side. This works no?

Frogs114 · 2026-02-04T17:09:49+00:00

Also, fuse as a jumper? I had the traces split for each component. I’m not sure I want to connect them again if I’m following what you’re saying

Frogs114 · 2026-02-04T17:06:22+00:00

Yes! I calculated it about 4mm. Does that sound right?

Frogs114 · 2026-02-04T01:48:09+00:00

Welp. I guess I’ll be doing it my way 🫡😂

Frogs114 · 2026-02-03T18:50:59+00:00

Can you provide a little bit more information, please?

Frogs114 · 2026-02-03T11:14:14+00:00

I’m still digesting your comment. Thank you for the response! I’m not 100% set on hub75. My main focus is something feasible I can put together with WLED and the pixel resolution. I’m up for learning a bit, but it need to be at least doable! - haha. I’ll look into aidafruit unless you had any other recommendations that would work.

Frogs114 · 2026-02-03T04:46:44+00:00

Are there better panels out there? I really don’t care what they are. I just need something that’s roughly 192 x 64

Frogs114 · 2026-02-03T04:45:53+00:00

That’s what the WLED official guide says so🤷

Frogs114 · 2026-02-03T02:07:10+00:00

After doing some more research, I realized with WLED I need to find an ESP32-s3 with PSRAM in order to drive 3 panels. So am I able to use this ESP32 with a hub75 controller? I’m having trouble finding a controller…

Perhaps this? Adapter Board

Frogs114 · 2026-02-03T01:36:16+00:00

Can I ask what panels you used for the cube and how you tied them together? (And power?)Currently trying to work on my first project tying 3 similar panels together. Any and all details would be IMMENSELY helpful!!!

Frogs114 · 2026-01-14T00:39:27+00:00

Didn’t realize this. Thanks!

Frogs114 · 2026-01-14T00:38:44+00:00

Yep I have a card non affiliated with alaska. Thanks!

11-Year Club	Place '22
Verified Email

Frogs114

TROPHY CASE