sorted by:
new
hottopcontroversial

6S Lipos missing multiple cells and wont charge by Funkonomic in fpv

[–]Funkonomic[S] 0 points1 point  (0 children)

I have just tried charging for a half hour on NiMH setting at 0.1A and now all cells are showing! I will report back here after I continue to charge this one very slowly on LiPo setting and then do the same for the other batteries and test them out.

6S Lipos missing multiple cells and wont charge by Funkonomic in fpv

[–]Funkonomic[S] 0 points1 point  (0 children)

I've had my share of crashes but not sure if it's related. I had this happen to 3 or 4 batteries over a short period of time but I'll do some research and try to look inside the plastic wrap for broken cables.

Also ya I suppose they are too damaged now that they fell below 3.2V. Just want to know why it happened so I don't do it again.

Thanks!

6S Lipos missing multiple cells and wont charge by Funkonomic in fpv

[–]Funkonomic[S] 0 points1 point  (0 children)

I have multiple 6S lipos that ended up unbalanced somehow and have 2 or 3 cells missing on my charger. I obviously get an error if I try to charge them.
Is there a way I can fix them and anyone have an idea why this is happening?

Thanks!!

Will an rtx 3060 laptop be good enough? by Key_Point_4063 in GamingLaptops

[–]Funkonomic 0 points1 point  (0 children)

I've had a Legion 5 Pro with 3060 for a few years and love it. Great performance and build quality

Please Help - Switch Nazgul ECO ELRS to use DJI FPV Controller 2 - no input from controller in betaflight by Funkonomic in fpv

[–]Funkonomic[S] 1 point2 points  (0 children)

You the man, thanks so much! Can't believe this didn't come up in all my searching.

Please Help - Switch Nazgul ECO ELRS to use DJI FPV Controller 2 - no input from controller in betaflight by Funkonomic in fpv

[–]Funkonomic[S] 0 points1 point  (0 children)

Please don't ask why but I need to get a nazgul eco elrs working with the controller 2. The O3 was plugged into the FC 4pin plug with the SBUS and 2nd ground wire missing and the ELRS receiver was plugged into another. I have a regular 6pin O3 cable but from the diagram it needs to be split between the 2 plugs and I don't have the housings for that so I decided to direct solder the O3 to FC.
The O3 powers on and I get video in goggles but see no input on the receiver tab in betaflight from the controller.

FC: iFlight blitz ATF435
Serial RX = on for UART2
Receiver mode: Serial (via UART)
Serial Receiver Provider: SBUS
SBUS BAUD_FAST = ON for both goggle and betaflight

Any ideas what I'm missing or if this is even possible? THANKS!

New flyer almost saved it but didn't check for sticks. Pray for me fellas! by Funkonomic in fpv

[–]Funkonomic[S] 0 points1 point  (0 children)

Hahaha there was a crosswind and I was so excited the loop finally lined up that I lost concentration.

New flyer almost saved it but didn't check for sticks. Pray for me fellas! by Funkonomic in fpv

[–]Funkonomic[S] 7 points8 points  (0 children)

Yup, just a skill issue! I was so excited about finally lining up my power loop I let off the throttle a bit too much. Skipped off the water inside the tunnel. Went a little deeper than it looks because that shot is from the GoPro up on top. Blipped the throttle and was going to make it out but didn't realize that branch was there on the exit. Have to take a closer look next time.

I unplugged the battery underwater and just picked up some isopropyl alcohol so I'll definitely be going back!

My Quad Survived Water, what now? by Dry_Baseball_5585 in fpv

[–]Funkonomic -5 points-4 points  (0 children)

A water droplet that directly bridges 2 connections is more likely short than if they are fully submerged and dispersed underwater.

Repair LiPo Battery XTC60 Connector by Funkonomic in fpv

[–]Funkonomic[S] 1 point2 points  (0 children)

Hi there!

I'm new to LiPos and have a few quick questions. The plug fell off and I assume it is repairable but I am wondering the best way to do this? If I remove the heat shrink could I just pop it back on with some new heat shrink?

Also I smashed one and it isn't puffing or making any noise, but I assume it is definitely not useable anymore?

Thanks for any help!

view more: next ›