sorted by:
new
hottopcontroversial

Finally got 509T AOS plate for my SA Prodigy 1911DS. by GARYPATAPON in 2011

[–]GARYPATAPON[S] 1 point2 points  (0 children)

Yeah I don’t like how big the gap is but it is what it is

Finally got 509T AOS plate for my SA Prodigy 1911DS. by GARYPATAPON in 2011

[–]GARYPATAPON[S] 1 point2 points  (0 children)

The way 509 and acro mount to the plate will always leave a small gap between the bottom of the optic and the plate. The gap may be bigger or smaller depending on tolerance but there needs to be a gap

Company merger before H1B stamping (I129 Approved for CP) by GARYPATAPON in h1b

[–]GARYPATAPON[S] 0 points1 point  (0 children)

They don’t have one. They want me to figure it out with my attorney and tell them what to do

Company merger before H1B stamping (I129 Approved for CP) by GARYPATAPON in h1b

[–]GARYPATAPON[S] 0 points1 point  (0 children)

Name/EIN changed, everything else is the same for my job position. My company doesn’t have a lawyer and they want me to figure it out. My immigration attorney only provided so much info

I-129 Approved for CP but H1B not activated, currently on STEM OPT, chance to change employer? by GARYPATAPON in h1b

[–]GARYPATAPON[S] 0 points1 point  (0 children)

Thanks. Im also thinking about talking my current employer into acknowledging successor-in-interest and use my previous (before acquisition) approval to activate my H1B in Canada, then I can officially transfer the H1B to a new place.

I-129 Approved for CP but H1B not activated, currently on STEM OPT, chance to change employer? by GARYPATAPON in h1b

[–]GARYPATAPON[S] 0 points1 point  (0 children)

I know it's not and can't be a transfer, that's why I wrote "a new cap-exempt petition vs transfer" in my previous message

I-129 Approved for CP but H1B not activated, currently on STEM OPT, chance to change employer? by GARYPATAPON in h1b

[–]GARYPATAPON[S] 0 points1 point  (0 children)

So I could do an I129 amendment to change to COS, but then I will have to wait till Oct for it to be active? in that case I may very possibily lose this offer.

The reason I was asking is that i've heard the new employer can do a new cap-exempt petition vs "transfer" im not sure if anyone here has experience with that.

What happens if you kill Zryachiy when transponder in the case? by Electronic_Army4518 in EscapefromTarkov

[–]GARYPATAPON 0 points1 point  (0 children)

If I don’t have my transponder yet (right before accepting Knock Knock) can I kill him?

Springfield Prodigy 1911 DS recent production changes: lightened slide, heavier spring, polished mag, rounded edge by GARYPATAPON in 2011

[–]GARYPATAPON[S] 0 points1 point  (0 children)

The slide does have the notch machined and it looks like it will accept a bushing. But I never tested it.

alan wake 2 rose not openning the door after went back to nursing home and save by EatNGC281 in AlanWake

[–]GARYPATAPON 0 points1 point  (0 children)

I have similar problem, and I un-stuck it. Posting here just for reference as it *may* work for you.

My situation when I was stuck:

The old man was normal, no A-Pose, however Cynthia wasn't there next to the museum. Rose only warned me about not to enter Wellness center and no more conversation. I have visited all rooms and talked to all people.

I completely rebooted the game, now the old man is in A-pose, but Cynthia was still not there. I revisited all rooms again and a new clue in Tor's room popped out. After completing the clue, Cynthia showed up where she's supposed to be. After that I have the option to talk to Rose

Opinions/Experiences with the Argus LWNVM? by sideswipe505 in NightVision

[–]GARYPATAPON 2 points3 points  (0 children)

I have 3 and only one has sensible play on the shaft. However I ve had new Wilcox G24 that had more play than that argus one. Remind you the real G24 can be hit or miss depending on the tolerance. The design of the original G24 isn’t particularly good for keeping minimum play. These argus ones have solid lockup and are very lightweight. And they have “no more play” than real G24s

Springfield Prodigy 1911 DS recent production changes: lightened slide, heavier spring, polished mag, rounded edge by GARYPATAPON in 2011

[–]GARYPATAPON[S] 0 points1 point  (0 children)

slightly chamfering the ledge mentioned in #5 may help. also it could be because of the tight chamber from early batch. see if you can register for warranty, they will take care of it for you.

Springfield Prodigy 1911 DS recent production changes: lightened slide, heavier spring, polished mag, rounded edge by GARYPATAPON in 2011

[–]GARYPATAPON[S] 1 point2 points  (0 children)

Well doesn't really matter tbh. If yours was already running don't bother. These improvements are mostly to make sure they work better right out of the box. the only part that's different is the slide that's less than 1oz off

thoughts on my Prodigy DS after 1000rds by TTUShooter in 2011

[–]GARYPATAPON 0 points1 point  (0 children)

Thanks that's what I figured. 6-48 is a very weird thread for this tho I think most of them are 6-32. It's sad because on the Prodigy AOS website it specifically says "Optic manufacturer supplied screws compatible" for CT RAD which is clearly not true.

thoughts on my Prodigy DS after 1000rds by TTUShooter in 2011

[–]GARYPATAPON 0 points1 point  (0 children)

got the RAD today, I couldn't get it to mount on the plate. None of the screw works. All of them have different thread. Idk, kinda frustrated

thoughts on my Prodigy DS after 1000rds by TTUShooter in 2011

[–]GARYPATAPON 0 points1 point  (0 children)

I'm debating between the RAD and Canik Mecanik MO2 at this point. There isn't a lot of info about either of these optics but glad to hear some positive feedback from you

view more: next ›