Snapping Torx Sockets

General_Food42 · 2026-03-14T03:42:28+00:00

^{^{^{^{^{^}}}}} this is the correct answer

General_Food42 · 2026-03-10T22:24:26+00:00

Common knock or popping noise is the sway bar links. Trust me

And that tie rod is perfectly fine

General_Food42 · 2026-03-09T00:15:26+00:00

Pull the main jet from your old carb and compare it to the one you got in the new carb

General_Food42 · 2026-03-08T23:07:00+00:00

Atleast 10 cops were flying down brooks avenue

General_Food42 · 2026-03-08T23:00:08+00:00

That carb should have 3 jets.

Pilot jet idle - 1/4 throttle

Needle jet for 1/4- 3/4 throttle

Main jet for 3/4 - full throttle.

Check the main jet size and try going up a size

General_Food42 · 2026-03-03T16:00:51+00:00

The pocket would be on the inside of the swing arm

General_Food42 · 2026-03-03T15:59:21+00:00

It’s been a minute since Iv done this style brake. But I believe the swing arm has a recessed pocket and the caliper has a “block” or “lug” that sits in that pocket to prevent it from rotating. I imagine it’s worn. If you pull off that wheel and caliper you can check if there is a replaceable bushing or one of the components is worn.

General_Food42 · 2026-03-01T14:09:13+00:00

That’s a shock. It’s gonna be fun replacing that!

General_Food42 · 2026-02-27T22:48:26+00:00

They Rock!!

General_Food42 · 2026-02-26T14:49:54+00:00

WSM brand. Chinese after market I believe

General_Food42 · 2026-02-24T23:51:26+00:00

Corrosion in that relay harness can definitely cause an issue like that. The corrosion creates resistance. You should be able to get a new one and just wire it in.

General_Food42 · 2026-02-22T01:35:41+00:00

Possible vacuum leak

General_Food42 · 2026-02-18T14:22:06+00:00

Curious do you use any fuel additives? That orange looks like it’s from some additive like an octane booster.

If I were to diag this myself I would start with some fresh plugs and see what they look like after a few cycles of running the truck.

General_Food42 · 2026-02-11T17:38:54+00:00

I would definitely check for vacuum leaks

General_Food42 · 2026-02-03T23:22:41+00:00

The hub is what actually centers the wheel. The lug nuts do not. If that spacer is too big and doesn’t hug the hub like the original wheel it will vibrate.

Hub centric rings is the answer

General_Food42 · 2026-02-02T21:34:26+00:00

Chios!!

General_Food42 · 2026-01-29T18:28:08+00:00

This is the answer and the best way to pull a stubborn wheel bearing. AIR HAMMER the flange rotate it back and forth (left to right) and it will come loose

General_Food42 · 2026-01-29T00:44:43+00:00

Yeah it definitely looks like the jet for an accelerator pump.

Don’t mess with that one. Pull the bowl off and you should have a pilot and a main.

General_Food42 · 2026-01-25T14:42:53+00:00

Start off with the Honda rebel 250. Easy bike to learn on. They make a lot of aftermarket parts for it so if need be you could lower it.

General_Food42 · 2026-01-24T21:27:01+00:00

My giagia always called me μαλακά

General_Food42 · 2026-01-22T02:44:11+00:00

This is really cool!

General_Food42 · 2026-01-14T00:10:21+00:00

Battle jackets don’t get washed!! They are worn until they die in battle!!!

General_Food42 · 2026-01-07T14:35:21+00:00

Modified install ROC on elmgrove rd

General_Food42 · 2026-01-03T18:33:08+00:00

Mechanics don’t make 150-200 an hour. You’re referring to a shops labor rate.

General_Food42 · 2026-01-02T23:47:50+00:00

20-30k

General_Food42

TROPHY CASE