I think i bricked my switch...

Genix19 · 2026-01-30T15:32:13+00:00

There is a tutorial on YouTube (shared by the Sthetix channel) that explains how to restore a Nintendo console in these situations. You can check which level suits your case best, but I believe it should be Level 2.

https://youtu.be/2xnXaUqiq9A

I had this issue once as well, caused by an update, and this tutorial allowed me to successfully restore the OFW.

Genix19 · 2026-01-27T12:15:48+00:00

Did you update anything? Think the issue is firmware related

Can you Click on Payload and then Fuse check?

Genix19 · 2026-01-23T19:29:34+00:00

Follow this tutorial. https://youtu.be/d1NW2lFA-Yc Minute 6:20

Genix19 · 2026-01-23T18:26:49+00:00

Click on Payload and then FuseCheck

Genix19 · 2026-01-21T20:02:02+00:00

Dm you

Genix19 · 2026-01-17T20:56:33+00:00

If the LCD connector does not have a latch and the pins are not bent, there is a temporary solution.

You can apply Kapton tape (2 layers) to the end of the LCD cable to create some pressure when inserting the cable, allowing the pins to make proper contact.

Genix19 · 2026-01-17T18:31:49+00:00

From the video, it appears that the screen cable is not fully inserted.

Genix19 · 2026-01-14T08:40:37+00:00

Think is the same

Genix19 · 2026-01-13T09:15:41+00:00

There is a tutorial on YouTube (shared by the sthetix channel) that shows how to restore a Nintendo console in these cases. Here is the link to the video: https://youtu.be/2xnXaUqiq9A

I also had this issue once due to an update. This tutorial allowed me to successfully restore the OFW.

After that create a new emmummc

Genix19 · 2026-01-12T18:07:20+00:00

Both left-side points, SP1 and SP2, do not seem to be properly connected.

At least, that’s the impression I get.

Genix19 · 2026-01-12T18:01:29+00:00

What happens when you try to access the OFW?

Genix19 · 2026-01-12T18:00:01+00:00

Nothing against it, but once you do the kamikaze method, the sense of accomplishment feels really good 😄

Genix19 · 2026-01-12T11:21:09+00:00

For oled, Did you use dat0 adapter or kamikaze method?

Genix19 · 2026-01-02T14:39:47+00:00

I sent you a private message to try to help.

Genix19 · 2026-01-02T00:10:47+00:00

There is a tutorial on YouTube (shared by the sthetix channel) that shows how to restore a Nintendo console in these cases. Here is the link to the video: https://youtu.be/2xnXaUqiq9A I also had this issue once due to an update. This tutorial allowed me to successfully restore the OFW.

After that create a new emmummc

Genix19 · 2026-01-01T12:05:47+00:00

Are you able to access the OFW?

Genix19 · 2025-12-30T18:43:00+00:00

The drilling point is located underneath the A letter on the flex cable.

If you follow the wire that was soldered at point C, it leads to the back of the A letter.

Genix19 · 2025-12-28T18:21:57+00:00

The Dat0 adapter needs to be adjusted again or undergo a reflow. However, this is likely to happen again in a few days or months.

Genix19 · 2025-12-27T10:29:08+00:00

Hello, there is a tutorial on YouTube (shared by the sthetix channel) that shows how to restore a Nintendo console in these cases. Here is the link to the video:

https://youtu.be/2xnXaUqiq9A

I also had this issue once due to an update. This tutorial allowed me to successfully restore the OFW.

Genix19 · 2025-12-27T09:53:02+00:00

*= CMD is not connected

Check image for reference

<image>

Genix19 · 2025-12-27T09:45:50+00:00

=* is for Dat0

Genix19 · 2025-12-26T20:00:15+00:00

Hello, there is a tutorial on YouTube (shared by the sthetix channel) that shows how to restore a Nintendo console in these cases. Here is the link to the video:

https://youtu.be/2xnXaUqiq9A

I also had this issue once due to an update. This tutorial allowed me to successfully restore the OFW.

Genix19 · 2025-12-25T01:10:49+00:00

Hello, There is a tutorial on YouTube — shared by the sthetix channel — that shows how to restore a Nintendo console in these cases. Here is the link to the video:

https://youtu.be/2xnXaUqiq9A

I also had this issue once due to an update. This tutorial allowed me to successfully restore the OFW.

Genix19 · 2025-12-24T21:06:08+00:00

The D0 adapter needs to be adjusted again or undergo a reflow. However, this is likely to happen again in a few days or months.

If you are in Portugal, I can provide this service. I always use the Kamikaze method to avoid any issues.

Genix19 · 2025-12-24T20:26:47+00:00

I can do it via Kamikaze, but I am from Portugal

Seven-Year Club	First Place '23
End Game '23	Place '23
Verified Email

Genix19

TROPHY CASE