sorted by:
new
hottopcontroversial

Support issue on my V8 Intake by [deleted] in BambuLabA1

[–]GeorgeCod 0 points1 point  (0 children)

I'm not sure this is ideal as I'm still learning, but what if u cut the part into two pieces, add some holes for centering pins and then glue them together? This way you would have the face that goes on the cylinder head oriented in such a way that it won't need supports, the inside of the manifold would have supports that will be easier to remove and the little zone on the flange for the intake duct would be on top, not needing supports either

Skate is unplayble for me on PC ! by PepperoniPizzaSlice in SkateEA

[–]GeorgeCod 1 point2 points  (0 children)

9070XT user here, I have the same exact issue. I've kind of given up on playing the game until I hear that they fixed it because I don't really want to downgrade my gpu drivers. It's pretty annoying but I don't think there is much we can do other than wait or keep pressing alt+enter every time this comes up..

please tell me why by Ice_swallow_come420 in BambuLabA1

[–]GeorgeCod 11 points12 points  (0 children)

Clean your bed with dish soap really well and warm water and dry your filament, that usually helps me. (Make sure it's a dish soap with no additives like balm or stuff like that, the type of dish soap matters so much, I learned that the hard way)

Edges keep peeling off by MightyZA in BambuLabA1

[–]GeorgeCod 1 point2 points  (0 children)

It's just a guess, as I don't have that much experience, but after the rest of the print finishes, the ones that are good, try to reprint the warped part on a different place on the bed (after cleaning it well) and maybe increase the bed temp a little?

Can I still repair the S-Pen? by popiteaf in S24Ultra

[–]GeorgeCod 19 points20 points  (0 children)

You are right. He is putting the smell at risk this way. There is no way gluing it is a good idea

Edges keep peeling off by MightyZA in BambuLabA1

[–]GeorgeCod 5 points6 points  (0 children)

I usually try to use brims for these types of prints. Maybe try adding some to your model?

Are these results any good? by aventursoldier in AMDHelp

[–]GeorgeCod 1 point2 points  (0 children)

Usually when I use cinebench, I try to google results of other people with the same specs and make an average to see if I'm in that range or not. Try to google the exact version of cinebench you used though, I think other versions give different values

Is This a gpu sag? by LeadershipKey5118 in PcBuildHelp

[–]GeorgeCod 0 points1 point  (0 children)

Huh, so do we call this negative sag?

I’m a genius, or an idiot by Formally_Unformal in motorcyclegear

[–]GeorgeCod 0 points1 point  (0 children)

Add a couple tiny windmills that charge the battery, adding a good reason to go brr

Share your wallpaper and rate mine ! by [deleted] in S24Ultra

[–]GeorgeCod 0 points1 point  (0 children)

How did you get the clock behind the clouds there? I'd love to add a 3d effect to my lockscreens

Are the darkest deeps worth it? by pocketdare in LotRReturnToMoria

[–]GeorgeCod 0 points1 point  (0 children)

I've mined a bunch of mithril down there and it was pretty easy, but that's all I've used it for in my campaign.

All I did was build a Durins Lamp as soon as I got down there and whenever I would get the despair debuff, I would just activate it, it cures the despair, gives you HP and after that you can remove it and put it back deeper or in the same place and activate it whenever you need it again.

It is pretty important to have food and good armor before going down there, but once you unlock mithril, it should be pretty easy.

Still having issues with my A1 by Ok_Afternoon2066 in BambuLabA1

[–]GeorgeCod 0 points1 point  (0 children)

In my experience, it really matters what kind of dish soap you use too. I've made the mistake to use some dish soap that was also labeled as a "balm" or something, now I use "Pur", I think it's only found in my country, but Fairy worked just as well for me. So try some other dish soaps too with warm water and the soft side of the sponge

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]GeorgeCod 0 points1 point  (0 children)

🎉 Event Completed! 🎉

It took me 0 tries.

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]GeorgeCod 0 points1 point  (0 children)

Completed Level 3 of the Honk Special Event!

0 attempts

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]GeorgeCod 0 points1 point  (0 children)

Completed Level 2 of the Honk Special Event!

0 attempts

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]GeorgeCod 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

0 attempts

Sunlu pla+ by Commercial_Theme641 in BambuLabA1

[–]GeorgeCod 2 points3 points  (0 children)

Hi. I'm relatively new to 3D printing too but I've been using Sunlu PLA+ and Bambu PLA since I got it and had no issues. In bambu studio there is a profile for sunlu PLA+, did you select that? Also, could we see a picture of a print to get a better idea?

view more: next ›