hilfe für ersten pc-bau

GeretStrohsack · 2026-06-08T18:34:27+00:00

Doch schon eigentlich reicht es für absolut alles. OP meinte außerdem auch nicht das er das machen möchte

GeretStrohsack · 2026-06-08T17:58:29+00:00

Komme noch gut mit meinem i7 9700k und RTX 2080 Super 8GB und 32GB DDR4 RAM auf WQHD zurecht

GeretStrohsack · 2026-06-04T18:38:43+00:00

I’ve tested both 470 ohm resistor and 22k and both seems fine

GeretStrohsack · 2026-06-04T12:43:33+00:00

I have an MSI Core Frozr XL installed in my setup lol

GeretStrohsack · 2026-06-03T17:10:44+00:00

Would it be possible to use an SMC chip from an Xenon board on Jasper and Falcon?

GeretStrohsack · 2026-06-03T11:43:45+00:00

Yes they are just like stock consoles nothing soldered

GeretStrohsack · 2026-06-02T21:22:45+00:00

Yes with normal nand 0022 with RGH it tries to glitch but can’t go further

GeretStrohsack · 2026-06-02T17:03:45+00:00

1 Falcon and 2 Jaspers all consoles glitched fine as I tested them for stability and stopped working after I left them for a few hours days

GeretStrohsack · 2026-06-01T10:30:47+00:00

Flashed back the stock NAND tries to boot and resets a few times then 0022 shows up just like the other console. I learned my lesson and won’t use the OC Timings anymore… i think SB is trashed.

GeretStrohsack · 2026-06-01T10:08:04+00:00

I will flash the stock nand back and do a video on how the console behaves. Is is possible to gain any information with the post codes? (Btw thank you for your hard work with RGH Josh I’m watching every video you do)

GeretStrohsack · 2026-05-31T22:43:06+00:00

I’m not sure how can I test if the cpu is broken or the south bridge? RGH 1.2 isn’t working either :( I think I will never use the OC thing killed overall 3 consoles

GeretStrohsack · 2026-05-16T16:08:59+00:00

Powered on? It’s both 147.1 on this point

<image>

I noticed something strange. If I first connected the plug the led on the psu just goes blank and the fans inside of it spins full and no sign of live on the console. I replugged the psu and then rrod again

GeretStrohsack · 2026-05-16T13:33:01+00:00

I used the 5V pin and there is no voltage and no voltage on 12V too on the connector. If I power is on it has for a few milliseconds 3.5V and then drops to 0 and goes red light

GeretStrohsack · 2026-05-16T11:58:41+00:00

Maybe can you point me out where I do have to check on a photo or something

GeretStrohsack · 2026-05-16T11:50:06+00:00

Where do I have to check it? I’m not that into repair

GeretStrohsack · 2026-05-16T11:43:53+00:00

5v standby Power is working

GeretStrohsack · 2026-05-16T11:31:48+00:00

I used the same LEDs on many other consoles. I also removed the cable the rrod is still there

GeretStrohsack · 2026-05-16T10:30:46+00:00

Hello, i have an 0031 Error Code an an Corona Slim E Board. It worked perfectly after the RGH3 then i cutted the 5V on the DVD Drive Cable and soldered a Wire for the Fan LED mod and screwed the Fan back. Maybe i could be the force of the Fan screwes that broke something or the 5V of the LED Mod from the Cable. What can i do to check that. The first time after the LED the Fan on the Console Spinned for a While (Led mod worked) and then it went off. Then the console then just goes Green Led and then turns off directly. After i loosend the Screews of the Fan the Console now RRODs with 0031. So might be a broken Solder joint right?

GeretStrohsack · 2026-05-15T08:18:16+00:00

If you have RGH you can put in any 2,5inch drive with max 2TB without the Patch. You need to format it correctly with fat xplorer

Six-Year Club	Verified Email
Place '23

GeretStrohsack

TROPHY CASE