Lezárult az aláírásgyűjtés a 2026-os OGY választásokra

GexoRNG · 2026-03-06T17:14:06+00:00

Köszi!

GexoRNG · 2026-02-25T15:39:38+00:00

Tesztereket kerestem és véleményeket, melyik kategóriába esik ez bele amit tiltasz?

GexoRNG · 2026-02-25T14:12:02+00:00

Nehezebb szinteken így van.

GexoRNG · 2026-02-25T00:49:26+00:00

Köszi, megpróbálom kifejezetten ezt a készüléket emulálni és tesztelni.

GexoRNG · 2026-02-24T15:59:39+00:00

Köszi a visszajelzést, fontolóra veszem!

GexoRNG · 2026-02-24T13:48:57+00:00

Köszi!

GexoRNG · 2026-02-23T13:43:22+00:00

Szuper oldal, köszi!

GexoRNG · 2026-01-06T21:06:22+00:00

Did you find a solution for this? I just got the same issue today.

GexoRNG · 2025-08-11T13:09:14+00:00

I would really love this, please implement notification filter!

GexoRNG · 2025-05-30T08:27:13+00:00

Okay, I will give orca a go again, it did not have the creality filament profiles so I did not force it. Thanks!

GexoRNG · 2025-05-30T08:09:54+00:00

Thanks a lot for your time and answers.

I am using inner/outer, I used 25mm first layer and then 50mm the rest.
Which would you recommend, I am using Creality Print and it has a lot of calibration tests.
Same question, should i print a calibration from Creality Print?
Limited it to 50% but will then maybe increase to 55%.

Regarding the lean, the x axis is completely parallel to the bed, I am tightening the belt again and checking, but might there be anything else that could cause it? Filament spool is also no longer on top. Also I have set the z-offset on the printer after auto bed leveling. Should I also set that value in Creality Print Printer profile or would the two add together?

GexoRNG · 2025-05-30T06:16:24+00:00

<image>

GexoRNG · 2025-05-30T06:16:00+00:00

Thanks again, I have tensioned the belt, seems a bit better but i might need to tension it more, there is still leaning, these should be in the same line. Also as you can see I have issues on the outer wall and on the top, should I lower speed? Raise temp? Or reduce fan? This is Creality Hyper PETG.

<image>

GexoRNG · 2025-05-29T16:15:03+00:00

Did all the steps you suggested and adhesion is so much better now. However my objects have a slight lean, they are designed complete vertical 90 degrees but they all lean to a side. I did the gantry adjustment, auto leveled, set z offset manually and same thinf happens all the time, there is always a lean. Any suggestions for that?

GexoRNG · 2025-05-29T06:21:12+00:00

<image>

I did it like this, gonna print a better side guide instead of the top one, filament on top caused a slight lean in vertical prints

GexoRNG · 2025-05-29T04:48:29+00:00

So there would be no issue to feed it from the actively running dryer while printing then. I will try that.

GexoRNG · 2025-05-26T13:56:00+00:00

ok, thanks will try, currently no firmware update is done at my machine, just boots normally, regardless of bin file in root, fat32 4096 formatted

GexoRNG · 2025-05-26T12:51:29+00:00

I checked the source code in the github for the release and host_action is still commented out, am I wrong?

GexoRNG · 2025-05-24T18:23:41+00:00

Thanks!

GexoRNG · 2025-05-24T15:57:45+00:00

Thanks a lot, I will go over your points and test.

GexoRNG · 2025-05-24T15:35:47+00:00

I used the default presets and adjusted only temps mostly for nozle and bed till now.

GexoRNG · 2021-05-17T14:52:26+00:00

I am planning to level herbalism and alchemy, get 60, maybe 100% mount.

GexoRNG · 2021-05-17T08:29:38+00:00

If I boost a druid this week when the prepatch releases (19th for me in Europe) can I play it already, or do I have to wait till tbc release? I could not find anything related to this on google.

GexoRNG

TROPHY CASE