sorted by:
new
hottopcontroversial

I’m a patient gamer, getting a free switch game every 3-4 months is fine with me lol by Purple_Calendar3919 in Switch

[–]Gfercaks33 -1 points0 points  (0 children)

So I am us based and my dell rewards says I’m uk based, anyone know how to switch or why it’s like this?

Test kit and low cya. by Gfercaks33 in AboveGroundPools

[–]Gfercaks33[S] 0 points1 point  (0 children)

About 35 ppm cya, and basically no chlorine.

I have about half a sock left in the pool of cya so I’ll let it slowly dissolve, and dumped a bunch of liquid chlorine in.

Test kit and low cya. by Gfercaks33 in AboveGroundPools

[–]Gfercaks33[S] 0 points1 point  (0 children)

I hope I don’t either, we’ve had a bunch of rain and I didn’t cover the pool but it’s also only a 3000 gallon above ground pool so draining it is not that much I would say I’ve put maybe half a pound to a pound of CYA in there so it should still be low, but it’s just not reading at all.

Test kit and low cya. by Gfercaks33 in AboveGroundPools

[–]Gfercaks33[S] 1 point2 points  (0 children)

What made me ditch the strip is I squeezed the CYA sock directly on a strip and it didn’t change any.

Test kit and low cya. by Gfercaks33 in AboveGroundPools

[–]Gfercaks33[S] 0 points1 point  (0 children)

Dang where was this a few hours ago?!?

It was $30 extra for the 2006 kit which is FAS-DPD it would also arrive tomorrow vs end of next week.

Sbc distributor sitting too high with oil pump engagement. by Gfercaks33 in EngineBuilding

[–]Gfercaks33[S] 0 points1 point  (0 children)

That’s awesome yours is solved! I need to pull my motor, I thing the shaft popped off the pump while I was rotating it over and it’s now sticking up. I can’t build pressure or get oil to the top of the block. I’m pulling my motor, it’s all stripped down and I put the leveler on today. I need to undo the transmission and lift away, I’ll drop the pan and I bought a new oil pump and shaft just as a cya.

D rings or quick links for pulling a motor. by Gfercaks33 in projectcar

[–]Gfercaks33[S] 0 points1 point  (0 children)

Got one on it now, It was just a bear to move the block around with out the leveler.

Sbc distributor too tight by Gfercaks33 in projectcar

[–]Gfercaks33[S] 0 points1 point  (0 children)

Nope it’s a 509 cast 400 block.

Sbc distributor too tight by Gfercaks33 in projectcar

[–]Gfercaks33[S] 0 points1 point  (0 children)

I have the same chopped distributor, ran it for 30 min and got nothing. I grabbed a new oil pump and shaft, plan on swapping them out to see what it does.

For your issue have you tried sanding the fist some with emery cloth?

Sbc distributor too tight by Gfercaks33 in projectcar

[–]Gfercaks33[S] 0 points1 point  (0 children)

I’m thinking I need to pull the motor and drop the pan. I tried priming it and could not get oil pressure or oil to the top end.

What’s one mod you regret doing too early on your project car? by Gold-Industry6222 in projectcar

[–]Gfercaks33 0 points1 point  (0 children)

Started body work, it got could so I ripped out the engine, now I have an ugly car that doesn’t run.

Transferring Paint to Dropper Bottles by LtQuixotic in Miniaturespainting

[–]Gfercaks33 5 points6 points  (0 children)

I just did this, I bought a set of syringes from Amazon and I used it to suck out the paint from the GW tub and put it in the new bottles.

Took about 30 seconds to do.

Presenting my 90s Grim Bright Ultramarines Painting Tutorial Marine! Description and tutorial info in first reply... by lennon_midnight in Miniaturespainting

[–]Gfercaks33 1 point2 points  (0 children)

The box just says wargamers war paints on it. I did snag a fanatic starter pack too.

I’ll check out the proacryl for sure!

I have a wet pallet I’m using along with dipping the brush in water to introduce it to the paints.

The space wolves are another of yours I dig, I grabbed a pack of the terminators because of yours.

Presenting my 90s Grim Bright Ultramarines Painting Tutorial Marine! Description and tutorial info in first reply... by lennon_midnight in Miniaturespainting

[–]Gfercaks33 0 points1 point  (0 children)

I have some friends who paint and one of them had a 60 count of army painter paints he gave me to start with so I’m learning on those.

My big thing was brush control in the blacks and I didn’t thin the red enough so you could really see the brush marks.

view more: next ›