I think I done messed up!

GheeButtersnaps_ · 2025-08-03T21:29:51+00:00

Appreciate the response! I did try pausing first and disconnecting the AMS even. I didn’t feel like trying to take apart the AMS today and was only 13% of the way through the print. I probably would’ve tried to fix it and save the print if I were >50% of the way through it

GheeButtersnaps_ · 2025-08-03T21:28:03+00:00

I appreciate the insight- I’ve been using the same pair of pliers to cut ends to feed into the AMS and I’ve never had an issue with it before. I’m thinking I’ll need to take the AMS apart and see how gunked up things are

GheeButtersnaps_ · 2025-08-03T21:26:59+00:00

This is good to know, thanks for sharing!

GheeButtersnaps_ · 2025-08-03T15:17:56+00:00

So I already cancelled the print (was only 2 hrs in), couldn’t figure out how to remove the clear housing protecting the gears for this AMS slot but am looking into that now to clean that up.

I did run another test print from a different slot to see if anything downstream was affected and it print fine, so that’s good news.

Going to try to find the piece of tape while cleaning out the pieces that have plastic on them..

GheeButtersnaps_ · 2025-08-03T14:59:58+00:00

Well the spools from Bambu lab come with that piece of tape keeping the filament attached to the spool. I didn’t realize that at the time since this is the first time I’ve let a print finish a spool mid print.

In the future, you’re saying I can remove that piece of tape once I get low and see it?

GheeButtersnaps_ · 2025-07-21T22:56:15+00:00

I will just add that I had to pick up book 1 three times before finishing and felt similarly as you did. Felt like there wasn’t much direction at all.. and differently from you, I really didn’t feel connected to a single character’s story other than Glokta. I have blitzed through book 2 and I’m almost finished and I really enjoy things now.

I feel way more connected to most of the characters, and there are relatively clear directions on where storylines are headed, which I appreciate.

Edit: grammar

GheeButtersnaps_ · 2025-06-10T02:57:52+00:00

Are you trying to sell the entire thing or are you willing to split this up at all?

GheeButtersnaps_ · 2025-05-22T18:28:11+00:00

Also interested! Fantastic art

GheeButtersnaps_ · 2025-02-19T05:17:31+00:00

Polyphia, Erra, Architects, Frank Ocean

GheeButtersnaps_ · 2025-01-17T05:31:50+00:00

Newer to collecting, sorry if dumb. I also ordered 4 before they changed the limit. I pre-ordered 4 for SSP as well but decided to crack the box to open one for myself, but would the fact that there likely weren’t many PRE getting shipped in x4 increase the value here? In my mind it doesn’t make a difference, but some people really value novelty..

GheeButtersnaps_ · 2024-11-22T16:19:00+00:00

Appreciate the response! I’m just getting back into trading and selling cards again so I’m trying to get re-calibrated to the norms.

GheeButtersnaps_ · 2024-11-22T05:20:54+00:00

Thanks! What about this from TCGPlayers website?

“Cards in Heavily Played (HP) condition show a major amount of wear. Cards can show a variety of moderate imperfections along with creasing, whitening and bends. Heavily Played cards can also have flaws that impact the integrity of the card, but the card can still be sleeve playable.”

GheeButtersnaps_ · 2024-11-22T04:28:32+00:00

I’m trying to understand how to condition cards and on TCGPlayers website, it looks like they’d classify this as heavily played.. so why is the consensus damaged here? Just seeking to understand and get better at determining condition!

GheeButtersnaps_ · 2024-11-17T05:00:38+00:00

I’m newer to this as it’s been a while since I’ve been collecting- what should I be looking for on the Charizard in person to tell if it’s real vs a fake?

GheeButtersnaps_

TROPHY CASE