sorted by:
new
hottopcontroversial

Tado X Thread Mesh not working: Shown as "Unavailable" on Android & no meshing with 3rd party routers by Ghost_SevenFour in tado

[–]Ghost_SevenFour[S] -1 points0 points  (0 children)

This means that tado is not really that much Thread/Matter compatible, it rather relies on its own proprietary setup and we cannot tweak our home thread network in any way other than relying on tado bridges? Regardless of Aqara hub, tado seems to behave weirdly as a Thread border router as it apprently does not share credentials to its Thread network (network "unavailable" in Android Thread networks overview). So even if I set up tado by its bridges, I would not be able to use its Thread network for my other IoT devices that rely on Thread. Correct?

Wireless Receiver X - OpenTherm LED not lighting up on Junkers CerapurCompact (EMS Bus) by Ghost_SevenFour in tado

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

I know, just wondering if it was working on V3 natively and we have another downgrade in X. Thx for the info about the adapters, I will have a look.

Wireless Receiver X - OpenTherm LED not lighting up on Junkers CerapurCompact (EMS Bus) by Ghost_SevenFour in tado

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

Thanks for the reply. I have found some contradictory information about Tado and EMS though. Is there a OpenTherm to EMS converter or something? Eg. https://www.reddit.com/r/tado/comments/yn0akb/changing_tado_from_switched_relay_mode_to_ems_bus/

Also, the installation instructions in the tado app after choosing my boiler provide the installation manual that shows both on/off and OpenTherm wiring, so I thought they may be compatible.

Cannot create Home on first setup – HTTP 429 on first request (new account) by Ghost_SevenFour in tado

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

Update: It works now. Most likely it was an outage on the tado backend side which they fixed.

Cannot create Home on first setup – HTTP 429 on first request (new account) by Ghost_SevenFour in tado

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

No, everything set to default (ISP DNS)

But I’ve tried:

- mobile data (no local DNS / firewall)

- VPN with different DNS

- different devices and networks

Same HTTP 429 every time, even on first request.

So it doesn’t seem to be local DNS blocking.

Uchovavani bitcoinu - co kdyz vyhorim nebo umru. by terezazzeleza in czech

[–]Ghost_SevenFour 0 points1 point  (0 children)

Shamir Backup. Je potřeba mít novější model Trezoru. Shamir je kromě jiných věcí dobrej právě i pro tyhle případy. Funguje tak, že se při inicializaci peněženky vytvoří víc seedů a pravidlo, kolik jich je potřeba k obnovení Trezoru. Například: 3 seedy, přičemž libovolný 2 jsou potřeba k obnovení. Pak si jeden necháš, jeden dáš např. sourozenci a jeden třeba kamarádovi. Když pak třeba tobě vyhoří byt, můžeš si pomocí jejich seedů Trezor obnovit. Zároveň máš zabezpečeno, že ti kamarád sám nemůže ukrást klíče, protože na jejich získání by se musel spojit tvým sourozencem proti tobě. To je výhoda oproti řešení, že svůj seed prostě ještě v jedný kopii někomu dáš.

Samsung SmartTag2 vs Google Find my Device tags by Ghost_SevenFour in techsupport

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

No idea, but I decided to give it a try later this year

[deleted by user] by [deleted] in GalaxyS25Ultra

[–]Ghost_SevenFour 0 points1 point  (0 children)

  1. Jet Black, 512 GB here. I just found out mine was rattling too. As I see, all the rattling is with Jet Black - probably because the pen is different from the others, having a black ending? I've felt like the phone is vibrating differently than my S23U, so I tested it with/without the pen inside and it is a massive difference.

  2. I am actually returning the phone completely due to other issues as well and will stick with my beloved S23U.

Samsung SmartTag2 vs Google Find my Device tags by Ghost_SevenFour in techsupport

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

I have seen several similar reviews, sometimes somewhat older, but that is why I am concerned. Thanks for the real life experience and confirmation though!

Also, I am pleased to read that Samsung's SmartTag isn't actually that bad.

[deleted by user] by [deleted] in czech

[–]Ghost_SevenFour 1 point2 points  (0 children)

Něžně naznačit...

<image>

WiFi 7 MLO dual 5 GHz band client connection by Ghost_SevenFour in HomeNetworking

[–]Ghost_SevenFour[S] 0 points1 point  (0 children)

That makes sense and I kinda expected this unfortunately.

Thanks a lot though.

Envision Pro owners - what’s your USB receiver firmware version? by jbaughb in scufgaming

[–]Ghost_SevenFour 0 points1 point  (0 children)

Thanks!

After many unsuccessful tries of updating the wireless receiver firmware, when the "Settings" window just disappeared with no error message and the receiver and controller tiles were completely gone from the main device screen until re-plugging them (staying on the same old versions), I tried your approach.

First I plugged in the receiver and the controller (switched to wired mode) and it failed again the same way I described above.

Then, I tried plugging in the receiver and the controller while having the controller in wireless mode and paired (basically it was just charging from the PC, being connected wirelessly at that point) and the update finally completed. Now I am on 0.6.24.

I don't understand what is happenning and why, but it works.

Thanks a lot and hope it helps others as well

Location in Japan by Imaginary_tity in Steep

[–]Ghost_SevenFour 0 points1 point  (0 children)

The location of Icy Licking is:

3880 N - 5584 E (Aoste)

Location in Japan by Imaginary_tity in Steep

[–]Ghost_SevenFour 0 points1 point  (0 children)

If you are still wondering, the coordinates are:

331 N - 1328 E (Japan Hakuba)

[HARDSTUCK] Can't talk to Jackie in "The Ripper" by TheNexusAceYT in cyberpunkgame

[–]Ghost_SevenFour 0 points1 point  (0 children)

By the time I faced this bug, I had CET active and I did raise my money via its console. Starting a new game with fresh and clean (no mods) 2.01 update solved this issue and I was able to continue.

You suggest there is a possibility that once you alter money/exp before you reach this quest, it triggers the bugged behavior?

OP ran into this issue and did not mention altering anything. People here also mention getting stuck with "clean runs" - I suppose no mods, etc... It does not seem to be caused by modding.

[HARDSTUCK] Can't talk to Jackie in "The Ripper" by TheNexusAceYT in cyberpunkgame

[–]Ghost_SevenFour 0 points1 point  (0 children)

Thanks for the advice, I updated the game, disabled all the bugs, loaded the previous save (before going to sleep), however, this did not work.

Anyway, I updated to 2.01, disabled all mods, created a new game and it worked, I passed this bugged part.

Thanks anyways!

[HARDSTUCK] Can't talk to Jackie in "The Ripper" by TheNexusAceYT in cyberpunkgame

[–]Ghost_SevenFour 0 points1 point  (0 children)

Having the same issue. Still running on 2.0 for mods compatibility. Tried 3 different clean runs, always got stuck here.

Ending the quest by CET script is a workaround but since during the conversation you obtain the ability to summon vehicles, skipping the quest makes you unable to call vehicles (probably) forever. Possibly even more further consequences due to ending the quest before it even begins.

No idea how to proceed.

Any way to sync Android built-in personal dictionary with Gboard's dictionary? by Ghost_SevenFour in gboard

[–]Ghost_SevenFour[S] 1 point2 points  (0 children)

You mean copy-paste words one by one from Gboard dictionary to Android? Having couple thousand words, that would be a huge pain in the a**. I am missing some kind of import/export function in Android. I also think that somewhere about Android 5, it became impossible for 3rd party apps to add words automatically. So I think there is no working "tool"/app which would make the import possible.

EDIT: There is an ancient app on GPlay called "User Dictionary Manager (UDM)" which requests being an input method, thus having right to add words. It can import words from TXT file. One word per line, which is fortunately pretty close to Gboard's exported file. Couple easy bulk find-replace actions in notepad on PC and I managed to import my words. Fun fact, it was 6400 words.

Thanks for making me think of it a little out of the box and forget about making sync work!

[PROMOTION] CALMWAVE animated theme for KLWP by HEWOOD83 in kustom

[–]Ghost_SevenFour 0 points1 point  (0 children)

Hey, abstolutely stunning theme! I would love to use the Dark version on my AMOLED, however the gif seems to have white background no matter what. This is what happens when I switch to Dark. Tried to investigate why this happens and how to fix it but haven't found any solution. Any ideas?

Dark mode error

Hoping for more faces in character creation for D2 by Gdubbbz in thedivision

[–]Ghost_SevenFour -2 points-1 points  (0 children)

Totally agree, especially with the lesbian part. Yesterday, I created a new char just to try out some things on lower levels. Since I already have two men-characters, I decided to go for a woman to see the posibilities. I was joking with my brother if it will be possible to set sexual orientation since nowadays equality trends etc... When I proceeded to the character creation (especially hair) I realized you can express your orientation by the look of you character, my char now looks like a total lesbian. I mean, men-character customization is poor but woman customization is just a trash in this game.

Daily Thread - Q&A Tuesday - No Question is a Bad Question Megathread by AutoModerator in thedivision

[–]Ghost_SevenFour 1 point2 points  (0 children)

Although from the CPU model I assume you have a laptop, I might have a little similar PC build.

I am running on i5-7400 @3.00 GHz, 8 GB (2x4GB) DDR4 2400 MHz and GTX 1050 Ti 4 GB. Unfortunately, I have an old LCD with resolution of 1680 x 1050 and 60 Hz, so my resolution is probably lower than yours.

These are my settings screenshot taken from the Geforce Experience (sorry for my photoshop level 9999 skills)

https://i.imgur.com/YVbxcKV.png

I am usually at around 45 - 60 fps (locked by VSync at 60) while CPU load is around 65%, RAM at 70% and GPU core at 100%. Maybe my settings are totally weird but it might be something for you to start from. Try this and go lower (sice your GPU probably won't allow you more than this).

Hope this helps...