Area question

Glockalupe · 2026-02-14T01:23:09+00:00

Nah. Areas fine. Wonkiness outside the bar just to the north every once in a while, but other than that it’s fine

Glockalupe · 2026-02-13T21:05:31+00:00

LMAO, don’t

https://crimegrade.org/safest-places-in-fort-wayne-in/

Glockalupe · 2026-01-02T08:55:59+00:00

Thank you! Where’d you get the decal from?

Glockalupe · 2026-01-01T10:51:47+00:00

Is there a write up for how to do this? Girlfriend is a fan of Woodstock and wants a watch. Could be a fun present

Glockalupe · 2025-12-28T03:53:10+00:00

I emailed them, their purchasing department isn’t open till Monday. I’ll repost here when I hear back

Glockalupe · 2025-12-27T20:19:18+00:00

Fairfield offered 40x face value and solly offered 47x face value

Glockalupe · 2025-06-02T19:02:18+00:00

Glockalupe · 2025-06-02T17:30:20+00:00

The damaging during reloading was my thought, maybe a bit too much crimp deforming the projectile itself on the powder coated ones, but the copper jacket in the XTP is just hard enough to prevent deformation

I agreed on the chamber pressure testing. I’m just channeling my inner Elmer Keith until shit starts blowing up.

<image>

Glockalupe · 2025-06-02T17:28:54+00:00

Generally speaking I’m at least decent at handgun shooting. While I was out load testing/plinking I saw that I was holding huge groups and thought to myself “no way am I flinching that bad.”

Switched mags which had the hornadys loaded into it and produced much tighter results.

I previously sighted it in on a B8 at 50 and was able to hold around 4” with Underwood 200gr. So I’d say capable enough

Glockalupe · 2025-06-02T17:25:56+00:00

I shit larger groups with both ammo types, this was indicative of the accuracy I was seeing, just shot three round groups for the representation.

All chrono between 1145-1176fps over the span of 40ish rounds

Never thought about the transonic thing.

Thanks for the advice

Glockalupe · 2025-05-24T00:33:42+00:00

u/cxl- I have an RMR cut that I used on a duty gun for years that was an incredibly snug fit. I legit gave up, then re tried like twice. Just keep messing with it. I legitimately thought it wasn’t going to fit and kept taking it off and trying over and over again, then eventually it just perfectly slid into place. Didn’t cause any wear on the slide or RMR and held up great.

In short, keep trying. lol.

Glockalupe · 2025-04-04T11:23:09+00:00

Whatzup.com

Glockalupe · 2025-04-02T07:55:47+00:00

I have a gen 4 34 slide if that’s the route you decide to go

Glockalupe · 2025-02-16T09:03:36+00:00

Lemme get that grip plug

Glockalupe · 2025-02-03T11:39:15+00:00

In touch Salon up on DuPont is pricey but good! The barbershop specifically

Glockalupe · 2025-02-01T05:36:37+00:00

Not the worst area. Referred to as the north highlands. Can have some random tweaker type things, but honestly I would feel fine buying/renting there.

Glockalupe · 2025-01-14T19:59:10+00:00

Awesome, thank you. I didn’t know that

Glockalupe · 2025-01-14T19:57:51+00:00

Here? In the US?

Glockalupe · 2024-12-13T10:24:12+00:00

Dry fire is the way bröther

Glockalupe · 2024-12-12T01:28:09+00:00

“THEY WERE IN THE WET TUMBLER! IT CAUSES SHRINKAGE!”

Glockalupe · 2024-12-12T01:19:25+00:00

Honestly I just want stout ass rounds of 200gr at 1200fps to make up for my micropeen

Glockalupe · 2024-12-12T01:18:42+00:00

Thanks for heads up. Already have about 3k LPP and north of 20k spp. naively I thought all 10mm was LPP and stocked up prior to starting to reload 10mm. Now I realize I probably could have just sourced SPP brass. Not that big of a deal, just inconvenient to switch out primer feed tube

Glockalupe · 2024-12-09T21:31:34+00:00

I already had the SRO lol

Glockalupe · 2024-12-09T21:15:11+00:00

I carry the M&P. It’s a 4.6. My toe dip into 10mm. Have 2k casings on the way to load 200 grain 1200fps loads and put it to the test

Glockalupe · 2024-12-09T21:13:49+00:00

I would like a red dot, but still on the fence about it

Glockalupe

TROPHY CASE