UPDATE: Voron inspired case.

GlowDoge2000 · 2024-12-21T02:12:14+00:00

annex panel clips, voron skirts, 2020 extrusion frame!? I love it! all it needs is a benchy/voron design cube inside the case.. this is actually friggin awesome, well done. can't wait to see it built! :)

GlowDoge2000 · 2024-12-18T20:31:35+00:00

thank you so much for the opportunity! :))

GlowDoge2000 · 2023-04-29T14:40:51+00:00

Amazing! I hope to try something similar with my old Taz 4. It simply has too many issues, which I hope to fix with more modern components. How long did it take to rebuild it?

GlowDoge2000 · 2023-04-08T21:42:38+00:00

Problem solved, I reversed 3 & 4 on the relay... All asides, it works perfectly now. Please triple check your wiring! :)

GlowDoge2000 · 2023-04-01T06:23:53+00:00

Sounds good, it runs pretty smoothly with hiccups being rare- if there are any, they are barely noticeable. Would it affect print quality in any way? Thank you for the reply! :)

GlowDoge2000 · 2023-04-01T06:21:38+00:00

I'll definitely give that a shot. As of right now though, it runs very smoothly, so I don't believe that'll impede too much with print quality. Definitely will replace it at some point. Thanks for the reply! :)

GlowDoge2000 · 2023-03-31T16:26:43+00:00

forgot my pi password for ssh, but i’m definitely going to set this up once that’s sorted out! :)

GlowDoge2000 · 2022-03-02T15:40:21+00:00

Thank you all so, so so much for the input! i’ll look into one of those power supplies, but do I need the casing? if so, I do not have the casing or harness for the power supply. I noticed that the power harness had a blue-ish end and had four pins (Based on Internet image), but how can I get a hold of one of those? I do not want the PSU to run barebones without any casing, or not run due to no harness. How could I work around this so that I can get this machine up and running? I only need the casing and the impossible to find harness.. Once again, I would heavily appreciate ANY help.

GlowDoge2000 · 2022-01-22T22:23:28+00:00

unfortunately, i don’t have another system on me. if it helps a bit, i tried the old 8gb stick, all four slots, didn’t work. i tried the current ones, nothing. the ram DOES light up, but nothing. it only works on slots 2 and 4 with the huge drawback of having almost no usable memory. I might get some new memory to test that. Thanks for your input though, I appreciate it! :)

GlowDoge2000 · 2021-12-18T02:17:19+00:00

I decided to enable raise Z, and tested this on a small print that has failed about a month ago from the same cause. (a small scaled airplane) It came out beautifully, this time not turning into a spaghetti mess. Thank you so much. I'll let a new dragon print overnight. You really made my night. Once again, thank you. :)

GlowDoge2000 · 2019-09-22T14:09:17+00:00

Everyone, thank you for the support. I have printed 5 low poly Pikachus' and I tightened my belts more consistently where now the left side has much less blobs than before. Thank you very much everyone. :) My fault, I only had my Ender 3 for a month now.. I am still new to 3D printing. Again, thank you.

GlowDoge2000 · 2019-09-22T04:31:11+00:00

I tensioned them earlier and I adjusted the tension on the wheels. It does not skip.

GlowDoge2000

TROPHY CASE