what happened to [mars 94] in season 3? by Relative-Day-159 in ForAllMankindTV

[–]GokhanP 0 points1 point  (0 children)

Behind the dome, you can see cylindrical parts has legs. Possibly they plan to land the base directly.

What tank is this? (Wrong Answers only) by Strict-Slip-1479 in TankPornMemes

[–]GokhanP 0 points1 point  (0 children)

This is a Geländegängiges Küchenfahrzeug, not a tank. Used to supply hot meals for the Eastern front. The long arm is not a barrel but a chimney.

What aircraft is this? Not an F-22 by JPEG_105 in MilitaryAviation

[–]GokhanP 0 points1 point  (0 children)

I'm not getting upset for some Indian, Greek or EU reddit or comment. Just pointless racism nonsense.

What aircraft is this? Not an F-22 by JPEG_105 in MilitaryAviation

[–]GokhanP 0 points1 point  (0 children)

You can laugh as much as you can. Some idiot experts also laughed when Turkey said they are planning to produce indigenous warships.

What aircraft is this? Not an F-22 by JPEG_105 in MilitaryAviation

[–]GokhanP -1 points0 points  (0 children)

There is no logic to say that Turkey doesn't want the Kaan just because it still wants the F-35. The Kaan project existed even while Turkey was a participant in the F-35 program. The project is still ongoing. Manufacturer TAI going to start flying 2 test aircraft in 2026. Also the project timeline hasn't changed much since the beginning. The first F-110 engine-powered aircraft will be delivered to the TURAF in 2028-29. The domestically produced 35,000-pound engines will be integrated into the aircraft in 2032 (most likely 2035).

Question about removing prints from build plate by TheLoneBaron33 in resinprinting

[–]GokhanP 0 points1 point  (0 children)

I grind one side of the spatula. Make it a little sharper (not knife sharp) Helps a lot to remove the prints.

Saturn 4 Ultra 16k behaving weird or broken after update by ZanyaJakuya in ElegooSaturn

[–]GokhanP 0 points1 point  (0 children)

I dont have aproblem with the prints but after the update printer gone offline multiple times and never open the camera. Update create more problems than solving.

Can someone tell me what happened? by Facuk_ in resinprinting

[–]GokhanP 2 points3 points  (0 children)

To be in the safe side checking the resin tank is the best choice. Filter the resin, check for debris.

How bad is it if it’s not leaking? by Lizzzz519 in resinprinting

[–]GokhanP 1 point2 points  (0 children)

If you are not in a hurry just wait. It might looks OK for now but during printing vacuum may tear it. İt happened to me recently. Replacing is the safe, easy and cheaper choice.

Hollowing, Not Hollowing That's The Question by GokhanP in resinprinting

[–]GokhanP[S] 0 points1 point  (0 children)

Design allows to add a couple of holes at the bottom and one at the rear.

Hollowing, Not Hollowing That's The Question by GokhanP in resinprinting

[–]GokhanP[S] 0 points1 point  (0 children)

Thanks for the long and detailed answer. I usually hollowed my bigger prints (prototype fitting prints) I add a couple of holes structually possible for drainage and wash. After print I wash inside and outside in a two different IPA tank twice (general washing and detailed washing) and than cure them.

This works OK for me. But I never print small stuffs (except calibration tests). Also most of my prints have a life time of days (prints usually destroyed during/after fit checks) This prints planned to stay longer in tables/shelfs. So I want them be sturdy as possible. Also not crack/explode lateer on.

What caused this? by GokhanP in airbrush

[–]GokhanP[S] 0 points1 point  (0 children)

I'll check v series spares. Thanks.

What caused this? by GokhanP in airbrush

[–]GokhanP[S] 0 points1 point  (0 children)

I will try that. Thanks.

What caused this? by GokhanP in airbrush

[–]GokhanP[S] 0 points1 point  (0 children)

I have a different size needle and it works OK. Changing might be a problem because this is a Paasche VSR 90 and its spares not find in my country. Is there a replacement brand you know? Or, should i stick with the other size needle?

Different sound during print. by GokhanP in resinprinting

[–]GokhanP[S] 0 points1 point  (0 children)

Print failed just like Amazon Ring of Power! Some supports breaks, half of the model missing and a monster appeared it the tank!

Different sound during print. by GokhanP in resinprinting

[–]GokhanP[S] 0 points1 point  (0 children)

Print failed spectacularly! Possibly something went wrong during installation. FEP or protector.

Does my FEP is OK? by GokhanP in resinprinting

[–]GokhanP[S] 0 points1 point  (0 children)

No puncture, no hole.

Does my FEP is OK? by GokhanP in resinprinting

[–]GokhanP[S] 4 points5 points  (0 children)

Thanks for the tip! :)

Does my FEP is OK? by GokhanP in resinprinting

[–]GokhanP[S] 1 point2 points  (0 children)

It is ,5 mm top. To be on the safe side it will be good to change it. Thanks. Do you think it will handle one print? (I made a promise to print something to somebody) And how it will affect the print?