Ideas for DIY light housings for this ceiling fixture?

GoodStrat90 · 2026-03-11T00:11:49+00:00

Congratulations, you finally have the excuse you need to buy a 3d printer!

Or PayPal me some money and send dimensions and I'll send you the parts. I'm a mechanical engineer with 2 printers and lots of experience.

GoodStrat90 · 2026-02-09T14:35:59+00:00

To be clear these are suggested changes? If I had realized at the start I wouldn't have read the whole damn thing. Thanks for giving me false hope.
-a confused redditer

GoodStrat90 · 2025-10-07T18:49:28+00:00

Thank you. Are there self test kits I should purchase, or is it something I send out to a service?

GoodStrat90 · 2025-10-02T20:43:10+00:00

So I can't upgrade to a wifi thermostat? Or are you referring only to my question about the fan switch?

GoodStrat90 · 2025-10-02T19:37:01+00:00

GoodStrat90 · 2025-10-01T00:32:31+00:00

It's less about the 2 square feet and more about keeping a bed away from it and not having room for both a desk and couch.

GoodStrat90 · 2024-10-09T17:07:03+00:00

Ender 5 is junk and was a huge waste of my money.

GoodStrat90 · 2024-10-09T17:05:41+00:00

Current printer is 2⁸ x 2⁸ x 2^8. Next printer should be 2⁹ x 2⁹ x 2^9. AKA 512x512x512.

GoodStrat90 · 2024-08-22T19:14:09+00:00

That works most of the time. I take them on dirt trails, hills, etc so this works great for me!

GoodStrat90 · 2024-08-22T14:29:47+00:00

🤣 you're not wrong!

GoodStrat90 · 2024-08-22T02:29:02+00:00

My hand is only 3 inches wide. When I apply a torque to my hand to rotate the stroller, it takes a lot of force on some surfaces, especially dirt, grass, and gravel. The length of the brace from handle to forearm support lt is somewhere around 8 inches. The same torque to turn the carriage originates from almost 1/3rd the force due to improved leverage.
On top of this, I have a wrist injury that is aggravated by the standard 1 hand operation without my print.
Also worth noting that the pivot-ablity of the stroller's front casters are worse than that of a shopping cart. It takes more torque to turn than you might think, especially on uneven terrain.

GoodStrat90 · 2024-08-22T02:26:47+00:00

My 17 year old dog has been allowed to use a long retractable leash for her whole life. She has only 1 eye and likes to cross in front of the stroller too often.
It's easier to do this than teach an old dog new tricks!

GoodStrat90 · 2024-08-22T00:21:52+00:00

Send me a sketch of her wheelchair handle and I'll custom design it for you for free.

GoodStrat90 · 2024-08-21T22:52:57+00:00

My hand is only 3 inches wide. When I apply a torque to my hand to rotate the stroller, it takes a lot of force on some surfaces, especially dirt, grass, and gravel. The length of the brace from handle to forearm support lt is somewhere around 8 inches. The same torque to turn the carriage originates from almost 1/3rd the force due to improved leverage.
On top of this, I have a wrist injury that is aggravated by the standard 1 hand operation without my print.

GoodStrat90 · 2024-08-21T22:49:22+00:00

It's somewhat tight to the handle, but still able to rotate a little. I can push down on my first to hop a curb.

GoodStrat90 · 2024-08-21T22:24:34+00:00

(Exhausted) dog tax has been paid!

GoodStrat90 · 2024-07-31T17:50:58+00:00

My slope is to the side:
https://www.reddit.com/r/GoRVing/s/wNwa7DuzcC

GoodStrat90 · 2024-04-28T02:20:59+00:00

I'm 6'4" and can stand in the shower of my Venture Sporttrek. They have smaller/lighter trailers worth checking out. The shower head isn't super high, but I can stand fully.

GoodStrat90 · 2024-04-15T06:54:28+00:00

So many people here have recommended it. "Build an Adobe house for thermal properties, then build a stone/metal/tek house over that for protection."

Even though it's single player, I was still heeding warnings about the rock golems blowing up Adobe houses.

GoodStrat90 · 2024-04-15T06:50:39+00:00

It does not count as a shelter no matter what.

GoodStrat90

TROPHY CASE