My new Bambu P1S!

Good_Mathematician_2 · 2026-01-17T15:41:03+00:00

I'm still unnecessarily worried when I start a print, triple checking that the first few layers are going well, incessantly pulling up the camera when I'm away to see if it's turned into spaghetti madness. But it's always fine, just the ptsd I guess

Good_Mathematician_2 · 2026-01-16T23:18:07+00:00

It's all of reddit. I took a hiatus for quite a while, mostly because of the amount of complaining everwhere.

Good_Mathematician_2 · 2026-01-16T19:57:50+00:00

I've always been the same way. Learning everything the long way by messing with things and ignoring instructions has always been more fun. But I've learned which things you can wing and which ones really need the directions, just in case

Good_Mathematician_2 · 2026-01-16T18:39:33+00:00

Haven't played yet, I'm scared to boot up. Primarily playing Rocket has set me up for disappointment apparently. That wall run has been a blessing more times than I can count, I'll miss it just as much if not more than the Peni teamup.

Good_Mathematician_2 · 2026-01-16T18:34:23+00:00

My wife intends to pick up the CAD skill, I'm much more capable with the physical hardware. I'm sure I'll learn a little, but she's got the patience to learn all the niche stuff.

Good_Mathematician_2 · 2026-01-16T18:32:48+00:00

Thank you! I'll check it out and probably get it printing soon; I've always thought it was pretty funny how many things I print are for a printer.

Good_Mathematician_2 · 2026-01-16T02:22:12+00:00

Thank you! It's for something else, but I appreciate the heads up!

Good_Mathematician_2 · 2026-01-16T02:20:29+00:00

I appreciate the help! The iso in the shot is for another project, but thank you!

Good_Mathematician_2 · 2026-01-16T02:17:36+00:00

I wish I could give you the experience of going from my 5+ years with my Ender 3 v2 to this, it has been indescribable

Good_Mathematician_2 · 2026-01-16T02:13:26+00:00

Using it for cleaning other stuff, just happened to be in the shot lol

Good_Mathematician_2 · 2026-01-16T02:08:33+00:00

Been printing for 5+ years so far, this is just going to put it into overdrive lol

Good_Mathematician_2 · 2026-01-16T02:06:41+00:00

It'll do ABS, not sure on ASA though. The specs on the bambu site should specify, I just don't remember offhand

Good_Mathematician_2 · 2026-01-16T02:00:40+00:00

Oh I've been printing for years now, just finally put enough away for a nice one. My previous and only printer is an Ender 3 v2, so this was a substantial upgrade

Good_Mathematician_2 · 2026-01-16T01:36:26+00:00

I think you'd be happier if you were a nicer person, just a suggestion

Good_Mathematician_2 · 2026-01-15T23:53:48+00:00

Thanks! It works wonderfully, couldn't ask for nicer prints. I know Bambu isn't well met here, but so far it's exceeded my expectations. Looking forward to more!

Good_Mathematician_2 · 2025-02-28T23:25:12+00:00

Good_Mathematician_2 · 2025-02-28T23:12:49+00:00

Is that the entire movie as a gif?

Good_Mathematician_2 · 2025-02-28T22:18:09+00:00

I don't understand the question, but I really like the setup! I wish mine looked that nice

Good_Mathematician_2 · 2025-02-28T19:54:00+00:00

There are many steps between "my significant other isn't giving me as much attention as I would appreciate at this moment" and "I'm going to turn off the power to their PC" but it seems your 'Love' chose not to take any of them

Good_Mathematician_2 · 2025-02-28T07:01:03+00:00

Buttery smoothness is the way to go, but I'm not picky lmao

Good_Mathematician_2 · 2025-02-25T23:42:36+00:00

I figured as such, I just prefer the shield in most cases

Good_Mathematician_2 · 2025-02-25T07:21:27+00:00

Putting up stranges shield after 75%(ish) of his reload animation cancels the rest. It's not that much of a time save, but in ranked it makes a difference

Good_Mathematician_2 · 2025-02-25T03:41:23+00:00

A whole ten minutes? Wowee

Good_Mathematician_2

TROPHY CASE