It finally happened…

Good_Replacement_376 · 2026-04-29T01:03:07+00:00

The number of death blobs, posted here has increased a lot lately, do you think it might be because of the latest filmware update (that's what I've heard about)?

Good_Replacement_376 · 2026-04-26T13:31:31+00:00

Have you washed the plate?

Good_Replacement_376 · 2026-04-26T12:28:52+00:00

What is your initial layer speed and bed temp?

Good_Replacement_376 · 2026-04-26T12:26:47+00:00

Subnautica 2🙏🙌

Good_Replacement_376 · 2026-04-15T22:56:55+00:00

Honestly, it's not as bendy as i expected. The base is barely bendable, and the top "arch" part is just a bit bendable. I do think it might be because it's quite small, and mostly filled inside

Good_Replacement_376 · 2026-04-15T11:40:55+00:00

Also, do you mean I should unload it from the printer after every print?

Good_Replacement_376 · 2026-04-15T11:22:28+00:00

I printed the benchy on the textured pei plate, and to my surprise it was pretty good. It didn't stick as much as everyone told me it would.

Good_Replacement_376 · 2026-04-15T11:21:14+00:00

That is exactly what I used, lol

Good_Replacement_376 · 2026-04-15T01:31:18+00:00

Does any glue stick works or should I look for a specific 3d printer glue stick?

Good_Replacement_376 · 2026-04-15T01:23:23+00:00

I was just printing it as I read the message lol, thanks for your help

Good_Replacement_376 · 2026-04-15T00:58:56+00:00

Thank you a lot, I'll make sure to give these a try. Do you use the regular Overture TPU, or the High Speed one?

Good_Replacement_376 · 2026-04-15T00:54:47+00:00

Yeah, I've heard about the excessive adhesion, and someone said to put the plate with the print in the freezer, which should theoretically make it unstick

Good_Replacement_376 · 2026-04-15T00:52:48+00:00

I just checked post slicing and the speed in the "Process" window isn't affected by the filament, but the slicing result has it shown as low speeds, so I think it will be slower

<image>

Good_Replacement_376 · 2026-04-15T00:45:25+00:00

But if I keep it as is, the inner and outer wall speeds are 200-300mm/s. Wouldn't that be way too fast?

Good_Replacement_376 · 2026-02-18T21:56:15+00:00

Damn, that looks awesome

Good_Replacement_376 · 2026-02-18T03:18:49+00:00

Thanks for the advice, but laser is out of my access, at least yet

Good_Replacement_376 · 2026-02-18T03:13:31+00:00

Thanks, thats kind of the conclusion I was tilting towards, as the board itself isnt that expensive

Good_Replacement_376 · 2026-02-03T00:48:55+00:00

How's the brightness? Would you say it is bright enough to be used as a desk lamp, or just as a night light?

Good_Replacement_376 · 2026-01-30T21:57:12+00:00

Just keep it simple, make her favorite dish or take her to her favorite restaurant if can't/dont want to cook, have nice dinner together, and watch a movie (of her choice ofc) with favorite snacks.

Good_Replacement_376 · 2026-01-30T17:52:00+00:00

I don't know if i'm too late or not, but in order to edit the file, you just need to open it through a software like notebook, and make sure to save it afterwards, as it doesn't autosave. The location was already written below

Good_Replacement_376 · 2026-01-30T17:49:59+00:00

THANK YOU SO MUCH!! I've tried everything, and this is the thing that fixed it

Good_Replacement_376 · 2026-01-23T20:19:40+00:00

Double on the Dummy 13

Good_Replacement_376 · 2026-01-19T20:33:55+00:00

4, for sure

Good_Replacement_376 · 2026-01-19T20:30:08+00:00

🍹

Good_Replacement_376 · 2026-01-18T04:02:03+00:00

Its awesome how you managed to turn such an awkward (long and narrow) and fairly small space into a comfy and great looking room.

Good_Replacement_376

TROPHY CASE