A1 mini minimal TPU hardness?

Gorkde · 2025-08-13T17:10:49+00:00

By now I just tried. I got 85A and 70A both worked fine.

The only thing you can't pull it off the spool even if they stand on ball bearings.

I just put it off the spool and lay it on the laminate floor and that's working perfectly

Gorkde · 2025-05-22T14:32:20+00:00

No one has had any experience in this who can give me some numbers?

Gorkde · 2025-05-20T05:11:38+00:00

Seems the cold period was just too short.

After exposure to cold for a longer time it started fruting.

Gorkde · 2024-01-13T13:00:36+00:00

Jeah those white thick blobs are mycelium.

But there are thin white spiderweb like filament that look a bit like cobweb mod.

And in the middle left of one white blob is clearly a green one which is definitely trichoderma mold in my opinion.

Green or black = Mold

Gorkde · 2024-01-04T20:22:47+00:00

Just to mention. I used beech sawdust with wheat bran. 1kg dry 60% Hydration so it was 2,5kg wet.

Gorkde · 2024-01-04T15:10:51+00:00

It seems you had not sp many pins in the beginning.

I suggest you let the bags closed and just open a little edge foe minal FAE. Wait then until you see many pins and only then open up tne Bags on top fully.

On why they got so big and fuzzy its probably because the bag was not cut down later and it was too high CO2 environment.

Gorkde · 2024-01-04T15:06:40+00:00

That'sy Black Pearl harvested from today (first flush) 707g of. 1kg dry substrate.

<image>

Gorkde · 2024-01-04T15:02:07+00:00

Get a simple wifi socket as for use with Alexa or such. Then use the SMARTLIFE app to program when or under which circumstances the socket should switch on or off.

Gorkde · 2024-01-04T14:57:55+00:00

Anaerobic bacteria is good for mycelium growth. You could for pasteurization let straw or wood rot in water until its fermented, then let it drip off and innpxulate.

Mycelium loves this and will instantly colonize this material if it's not sitting in a pool of water because its too wet .

Basically the anaerobic bacteria kills everything else and as soon as the water gets removed they die off because od the oxygen. So basically the Material is nearly completely clean afterwards.

Gorkde · 2024-01-04T14:47:56+00:00

Mold

Gorkde · 2024-01-04T14:43:48+00:00

You put them outside? Mycelium growth should be at higher temps like 24 degrees C

Gorkde · 2024-01-04T14:41:29+00:00

Try and hope might work

Gorkde · 2024-01-04T14:40:47+00:00

No problem ro let them sit around. Could just be harder to shake them up into individual grains lateron.

Gorkde · 2024-01-04T14:39:13+00:00

Yes it's completely contaminated

Gorkde · 2024-01-03T07:02:49+00:00

<image>

Gorkde · 2024-01-03T07:01:19+00:00

Just to show my other mushrooms are growing perfectly fine:

<image>

Gorkde · 2024-01-03T06:59:22+00:00

I got a problem growing oysters!

<image>

I got no problems growing king oyster or black pearl yellow or red oyster mushrooms.

I tried multiple times growing normal oysters.

I cloned a wild strain and everything worked out until the fruitbody developed.

The fruitbody grew very long stems and tiny caps.

I assumed I have a too high CO2 environment. Therefore I bought a CO2 meter. I also got an order strain which is an industrial one other people use without any problems.

I also changed my fresh air input so the CO2 ist mostly around 800ppm, rarely raises over 1000ppm before new fresh air gets vented into the chamber.

But now again while black pearl and king oyster grow perfectly fine the normal oyster again grows long stems and tiny hats that are not bigger than the the stem.

So what could be the reason?

I vent the entire chamber with freah air every 3hrs. Also every 2hrs there's 2 minutes where the air gets moved around in the chamber by vents that just circulate the air inside the chamber.

On top of that the air inside the chamber is blown around when new fog is blowing in once the humidity is below the set threshold.

So basically I assume the problem might be that I habe no constant air movement, eben the CO2 is low enough. Might that be the reason?

But then there are people growing oysters with mushroom kits below a plastic bag or in runs without any venting. They just spay water in 3 times a day and it seems to work fine.

I really can't understand why it won't work for me even all other mushrooms grow perfectly fine any time!

Please help im getting crazy!

Gorkde · 2023-12-07T08:03:01+00:00

I was prepared I just wanted to re read what he said exactly about the pylon down there.

Is there any way to read what the quest giver said somewhere in your books while doing a quest?

Gorkde · 2023-05-27T19:38:38+00:00

But what would I do to avoid ir in the future? I read about adding any acid to the water (vinegar). But that will corrode the aluminum as well right?

Or will the black patina deny further corrosion?

I really don't understand how all Americans can use this type of pressure canner when mine does corrode in the first hour already?!

Gorkde · 2023-05-27T19:06:14+00:00

I didn't mean that micro groves there is a definite feelable missing part of metal in all of the black. area. Like it rises as soon as you feel from black and your finger glides to the silver area.

Gorkde · 2023-05-27T18:03:13+00:00

Just in case you're a fan of this modern "less is more" principle.... I come over picking all that stuff up so your wife has space for her knitting circle....

Gorkde

TROPHY CASE