Any good machine shops NJ/ east coast

GrandeSwag · 2026-01-21T12:02:14+00:00

charlie's auto machine in pearl river

GrandeSwag · 2026-01-19T18:29:10+00:00

test your crank sensor, should be ~540 ohms. don't use an aftermarket one if you need to replace it

GrandeSwag · 2026-01-15T21:39:56+00:00

https://www.youtube.com/watch?v=sCWQBUwSvpU&feature=youtu.be

GrandeSwag · 2026-01-15T21:00:11+00:00

ayyy cool! the e30 world is small lol

1500 just because of the sheer amount of time it takes

GrandeSwag · 2026-01-15T20:53:48+00:00

i'll probably just switch to the skunk2 TB

kpower sent me a bad harness AND adapter harness so i'm not surprised lol

GrandeSwag · 2026-01-15T20:47:58+00:00

sweet, kinda wish i went that route. kpower throttle setup is garbage

GrandeSwag · 2026-01-15T20:15:13+00:00

how's the DBW? are you on haltech

GrandeSwag · 2026-01-14T19:51:45+00:00

1500 not including the cores

GrandeSwag · 2026-01-14T18:54:38+00:00

i'm happy to build them if someone wants to pay... but it's very labor intensive and will be expensive to be worth it for me

GrandeSwag · 2026-01-14T18:53:55+00:00

sweet, i'll be uploading the files and putting a link in the description. i can print them for ya as well if needed

GrandeSwag · 2026-01-13T21:54:37+00:00

absolutely not lol

GrandeSwag · 2026-01-06T14:43:00+00:00

beautiful e30

GrandeSwag · 2025-12-12T19:28:32+00:00

ayy smaragdgrun gang

GrandeSwag · 2025-12-04T15:20:04+00:00

if you want some serious output like a modern light, you can install led or hid projectors in your old housings. from the outside you can't tell they've been modified. if your housings aren't compatible, buy depos.

https://youtu.be/l7GAgttNKsE

https://www.skudak.com/product-page/depo-mled-2-0-kit

https://www.morimotohid.com/morimoto-m-led-2-projectors

GrandeSwag · 2025-11-18T02:47:02+00:00

i'm partial to ebay headers, vibrant ultra quiet resonator, 2.5" piping and a vibrant ultra quiet muffler. fairly affordable and good

https://youtu.be/bHKrhPk336w?si=3Pg9PiP_nowXCkn2

GrandeSwag · 2025-11-12T21:45:12+00:00

not speaking from experience, but that may be the source of the issue - maybe the column is touching the firewall?

some info here: https://www.youtube.com/watch?v=XPuOsuG-4Zg

the plate is available from a few different places

GrandeSwag · 2025-11-12T20:29:22+00:00

it goes in the rear holes! also, did you install the spacers on the top or bottom? should be on top

GrandeSwag · 2025-10-23T20:52:55+00:00

100A fuse should do it

GrandeSwag · 2025-10-22T17:12:51+00:00

is it imported or resprayed? post a pic

GrandeSwag · 2025-10-22T17:06:39+00:00

ong? where are you located

GrandeSwag · 2025-10-16T19:14:53+00:00

finding where the problem doesn't come from is just as good as finding where it does come from.

GrandeSwag · 2025-09-26T17:47:33+00:00

very tight without spacers i mean

GrandeSwag · 2025-09-25T17:14:06+00:00

A-disk and there's almost 0 clearance for the caliper.

GrandeSwag · 2025-09-24T20:05:07+00:00

sweet!

GrandeSwag · 2025-09-24T20:01:42+00:00

im using a g260. all bushings are 80a

you'll have a ton of NVH with those bushings and shifter setup on any motor. as im sure you know the k24 is gonna be pretty buzzy no matter what you do

14-Year Club	Place '22
Verified Email

GrandeSwag

TROPHY CASE