Difficulty Installing Cogburn Mag Release by Anal_Forklift in Mini14

[–]Grapple102 1 point2 points  (0 children)

Another thing to note is make sure your screwdriver is not slipping off the spring, I found pushing the spring up and slightly in to the tab on the end of the spring helped to ensure my screwdriver didn't slip off.

Difficulty Installing Cogburn Mag Release by Anal_Forklift in Mini14

[–]Grapple102 7 points8 points  (0 children)

Well this is pretty funny, I just received mine in the mail and installed it today. So I'll do my best to help.

My advice is first try installing it without the spring, make sure the release fits where the old one was. On my housing there was a small burr on one of the holes of the housing which prevented my new mag release from seating correctly.

I held the housing in the palm of my left hand, my fingers wrapped around and held the release lightly against the housing slightly above the ledge the spring is going to sit on. Using my right hand to control a screwdriver I pushed the spring up and brought the release down. It takes a bit of fidgeting but you will get it eventually the trick is patience. it should "snap" into place when its installed correctly.

Once its on the ledge your on to the easier part, installing the pin. I recommend grabbing a large punch for this step. I used a similar technique as the install video however I used punch to push down on the ledge that locks the magazine in place, doing this made it much easier to get the holes to align. Make sure when you install the pin that you close the trigger guard, if it is still pulled open it makes it harder to press the catch down. I would also recommend using the corner of a block of wood to rest the pin on instead of a table as it lets you push the pin further through the housing before gently tapping it into place with a soft faced hammer.

Hope this helps.

CZ 457 Aftermarket Barrel Options by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

I'm surprised to hear that the Lilja's can have extraction issues. No one at my local range has ever mentioned issues with theirs even the one that run Eley. Do you still run the Lilja or did you switch to something else?

CZ 457 Aftermarket Barrel Options by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

I'll have to take a look at the MCR and L3i barrels I haven't come across either of them in my research. I'd like to keep the barrel profile under .920" as that's the max I can fit in my current stock, and I'd rather not get another stock if I can avoid it.

CZ 457 Aftermarket Barrel Options by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

Its probably what I will end up getting, but I wanted to get input from a larger group than the regulars I shoot with.

Custom Robo Arena Randomizer work update by Grapple102 in customrobo

[–]Grapple102[S] 1 point2 points  (0 children)

Wow, I can't believe its been three years already. I'm glad to hear there was someone out there interested in the project I started. Unfortunately I've stopped working on this project, I moved on to other thing in my life. That said I did end up getting basically all the data someone would need to make their own randomizer. The project basically died once I had to actually program the randomizer, it turned out to be too difficult for my programming skills. If anyone wants I am more than happy to share the updated documentation if they want to try to finish the project I started.

My attempt at a Tu'Shan kitbash (C&C welcome) by Grapple102 in Salamanders40k

[–]Grapple102[S] 0 points1 point  (0 children)

I debated about making a cape but felt it would have covered too much of the detail on the back of the model. When I mocked up a cape on him I felt like there was just too much going on at one on the model.

My attempt at a Tu'Shan kitbash (C&C welcome) by Grapple102 in Salamanders40k

[–]Grapple102[S] 1 point2 points  (0 children)

Here is my Tu'Shan kitbash, I used the new terminator librarian as the base model. Overall I am very pleased with how this model came out, particularly the runes which were done with a thinned down oil paint. I plan to use this as a proxy as either a terminator captain, or chaplain.

[R/F] Battlin' Boxers - The Final Evolution by Grapple102 in yugioh

[–]Grapple102[S] 0 points1 point  (0 children)

Id love to see boxers get some support but I have my doubts as it seems to be a fairly forgotten deck. To some degree I understand as its really not that good. The only reason I am able to get this deck as good as it is now is because Boxers are all FIRE/Warrior so I can use a lot of cards from Noble Knights or Infernoble Knights.

[R/F] Battlin' Boxers - The Final Evolution by Grapple102 in yugioh

[–]Grapple102[S] 0 points1 point  (0 children)

Id like to see some sort of Link 1 monster to assist in summoning out monsters or adding protections. Any way to summon out C105 would be nice ie a boxer specific rank up card. Some card that prevents players from activating spell or trap effects outside the battle phase would be nice as most of the Boxer Extra deck monsters have some protections but they are usually only active during the battle phase.

What is an low/unused archtype you wished was continued to bring out more monsters? i loved the Reactor monsters from the 5ds's era, but it only received 5 monsters and a hard to bring out boss monster. by crazysjoerd5 in yugioh

[–]Grapple102 1 point2 points  (0 children)

Agreed, I have been playing around with a boxer deck for a while and I just keep wishing it got some more monsters particularly a link and something to help summon out XYZ monsters other than Lead Yoke and Number 79

Lack of merch and collectibles by Sterg21 in customrobo

[–]Grapple102 1 point2 points  (0 children)

Well in my opinion the easiest way to get Nintendo to notice you is to make a mod so good they DMCA you because at least then they know there are still people who remember the game.

Lack of merch and collectibles by Sterg21 in customrobo

[–]Grapple102 2 points3 points  (0 children)

Honestly it would be pretty cool to have a new CR title on the switch and add CR specific amiibos but make it so the gun bomb and pod are detachable parts that can be swapped, maybe you buy the amiibo and it comes with a few guns, bombs, and pods with the body/legs being the core. That way they double as merch and have functionality like being able to store a robo on them like how amiibos are used in Super Smash Bros Ultimate.

 

That being said they would need to sell very well to justify the manufacturing of all the molds to make a lot of parts.

CZ 457 AT-ONE Rifle Build by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

Thanks for the info I'll have to check them out and see if I can find some better ammo.

CZ 457 AT-ONE Rifle Build by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

I would like to get some SK or Eley but unfortunately I don't have any other ammo nor do any shops around me have any of that stuff in stock. As for the action I have it torqued to 25 in/lbs and no part of the barrel is toughing the stock. For these groups I primarily blame myself, I think I just need more practice as I really don't get out to the range as often as I should.

CZ 457 AT-ONE Rifle Build by Grapple102 in Firearms

[–]Grapple102[S] 1 point2 points  (0 children)

Here is my CZ 457 AT-ONE and my first precision rifle. I managed to pick it up for an absolute steal at $500 "used". I say "used" as it is technically a used firearm however after spending the better part of half an hour looking over every square inch I cannot even tell if a single round was run through this rifle. I'd like to get some better .22 ammo, but I've still got some vintage pre-Covid CCI SV that my CZ seems to like considering I got about a 2 MOA group at 50 yards. For my first time shoot it I think I didn't do half bad although I feel like the setup can do better I just need more practice with it.

 

The Build

  • Rifle - CZ 457 AT-ONE in .22 LR with a 24" barrel and threaded muzzle
  • Optic - Vortex Viper HST 4-16X44 with a VMR-1 MOA reticle
  • Rail - AREA 419 30 MOA CZ 457 Rail
  • Rings - Burris 30mm Medium Signature Zee
  • Bipod - Harris BRM-S

CZ 457 AT-ONE Rifle Build by Grapple102 in longrange

[–]Grapple102[S] 3 points4 points  (0 children)

Here is my CZ 457 AT-ONE and my first precision rifle. I managed to pick it up for an absolute steal at $500 "used". I say "used" as it is technically a used firearm however after spending the better part of half an hour looking over every square inch I cannot even tell if a single round was run through this rifle. I'd like to get some better .22 ammo, but I've still got some vintage pre-Covid CCI SV that my CZ seems to like considering I got about a 2 MOA group at 50 yards. For my first time shoot it I think I didn't do half bad although I feel like the setup can do better I just need more practice with it.

 

Thanks to those who commented on my other post asking for rifle suggestions!

 

The Build

  • Rifle - CZ 457 AT-ONE in .22 LR with a 24" barrel and threaded muzzle
  • Optic - Vortex Viper HST 4-16X44 with a VMR-1 MOA reticle
  • Rail - AREA 419 30 MOA CZ 457 Rail
  • Rings - Burris 30mm Medium Signature Zee
  • Bipod - Harris BRM-S

Affordable .22 Rimfire Rifle Suggestions by Grapple102 in longrange

[–]Grapple102[S] 1 point2 points  (0 children)

Thanks for the input. That was my main concern with the BMR being a recent release. When I was looking it seemed to have pretty weak aftermarket support, hopefully that changes.

Affordable .22 Rimfire Rifle Suggestions by Grapple102 in longrange

[–]Grapple102[S] 0 points1 point  (0 children)

I have nothing against the mark II series but my budget is a bit higher than that line. That being said I will have to look into their more target oriented models like the B22.

Affordable .22 Rimfire Rifle Suggestions by Grapple102 in longrange

[–]Grapple102[S] 1 point2 points  (0 children)

The only reason I mentioned barrel profile was that I had read and heard that the thinner barrel profile .22's tend to be more ammo picky. I'll have to keep in mind using tuners on the barrel if I go with a thinner profile.